Advertisement
Quick Links
Photoelectric Sensor
AC/DC:Relay output
DC:Transistor output
V2 SERIES
･V2T-7000□□□
･V2R-1200□□□
･BGS-2V□□□□
INSTRUCTION
MANUAL
◦Confirm if the item meets your needs.
◦Before the use, you should first thoroughly read
this manual and operate correctly as mentioned.
◦You should keep this manual at hand for proper
use.
Protection
Protection
◦Adjusting the optical axias.
◦Through-beam type
1. Install the emitter and the receiver opposite to
each other so that the optical axis lines up.
2. Swing the emitter and the receiver vertically
and from side to side, and fix each at the mid-
point in the range where the indicating lamp at
the receiver lights up.
◦Reflection type
Swing the sensor vertically and from side to side,
an and fix it at the mid-point In the renge where
the indicating lamp lights up.
V2 series
※Through beam 54
Retro‑reflection 29
BGS 54
Output indicator(Orange)
Stable indicator(Green)
M4 Screw
Bracket
Through
beam
Cable type
Ｖ2Ｔ-7000
Connecotor type
－
Detecting distance
70ｍ
Light source
Supply voltage
DC24～240Ｖ±10% AC24～240Ｖ±10% 50/60Hz
3ＶA ｍax.（class A）
Current consumption
4ＶA ｍax.（class B）
Response time
Hysteresis
Control output
Relay 1C DC30Ｖ 2A / AC250Ｖ 3A ｍax.
Operation mode
Sensitivity ajustment
Indicator
Ambient temp./humidity
Storage temp./humidity
Environmental illuminance
Protection category/material
※ 1.Reflector Ｖ-61
24〜240V DC 24〜240V AC
Brown ①
10〜30V DC
+V Light ON
0V Dark ON
White ②
Black ④
Control output
Blue ③
0V
Brown ①
10〜30V DC
Black ④
Control output
No.①～④ corresponds to pin
○
+V Light ON
No. of connector
0V Dark ON
White ②
Blue ③
0V
◦Adjusting the sensitivity control
1. S e t t h e d e t e c t a b l e
object at the detection
position and turn the
s e n s i t i v i t y c o n t r o l
slowly from MIN toward
MAX until the output
indicator(orange) lights
up. Call it position A.
2. R e m o v e d e t e c t a b l e
o b j e c t a n d t u r n t h e
s e n s i t i v i t y c o n t r o l
from MAX toward MIN
A
p o s i t i o n w h e r e t h e
output indicator(orange)
is extinguished. Call it position B.
3. Point C midway between A and B is the
optimum sensitivity position.
45
20
5.5
Sens. adjustor
20
43.9
2m cable φ6.3(AC/DC)φ3.8(DC)
V2 series AC/DC type
BGS
Retro-reflection
(polarized filter)
Long range Middle range Short range
Ｖ2R-1200
BGS-2Ｖ100 BGS-2Ｖ50 BGS-2Ｖ30 Ｖ2Ｔ-7000D（N，P） Ｖ2R-1200D（N，P） BGS-2Ｖ100（N，P） BGS-2Ｖ50（N，P） BGS-2Ｖ30（N，P）
－
－
－
0.01～12ｍ※1 25～100cｍ 15～50cｍ 10～30cｍ
2ＶA ｍax. （class A）
2.5ＶA ｍax. （class B）
15ｍs ｍax.
－
20% ｍax.
5% ｍax.
Light ON
Output indicator （orange LED） / Stable indicator （green LED）
-25～55℃ / 35～85%RH （No condensation or freezing）
Sun light： 10000lx ｍax. Incandescent light： 3000lx ｍax.
IP67 （IEC 144）/Case： ABS （ Glass fiber include） Front cover： PC （PMMA for retro-ref. type）
V2 series
10〜30V DC
①
②
④
③
M12 Connector
◦Other precautions
○ It is dangerous to wire or attach/remove the
connector with the power on.Make sure to turn
off the power before operation.
○ Be careful not to install the sensor at the
following locations, for it may otherwise
malfunction:
• Where a lot of dust, vapor, or the like is preset
• Where corrosive gases are produced
• Where water, oil or the like flies directly onto
B
the sensor.
• Where strong vibration or shock is caused to
the sensor.
○ The product is not designed for outdoor use.
○ Do not use the sensor in a transient state at
power on.（about 150 ms）
Ｃ
○ Avoid wiring together with high voltage or motor
line in order to prevent the sensor from noise.
○ The performance may depend on the individual
units or the condition of detected product.
○ T h i s p r o d u c t i s n o t a n e x p l o s i o n - p r o o f
construction. Do not use the product under
flamemable,explosive gas or detected product.
○ Do not use the product in water.
○ Do not disassemble,repair,or convert the
p r o d u c t . F a i l u r e t o d o t h i s m a y c a u s e
failure,fire,or electric shock.
○ Operate within the rated range.
！
This product cannot be use as a
safety device to protect human body.
70
23.7
Only DC type
M12 connector
V2 series DC type
Through
Retro-reflection
beam
(polarized filter)
Long range
－
Ｖ2Ｔ-7000CD（N，P） Ｖ2R-1200CD（N，P） BGS-2Ｖ100C（N，P） BGS-2Ｖ50C（N，P） BGS-2Ｖ30C（N，P）
70ｍ
0.01～12ｍ※1
25～100cｍ
Red LED
DC10～30Ｖ Including ripple （P-P） 10%
35ｍA ｍax.
0.5ｍs ｍax.
3ｍs ｍax.
－
15% ｍax.
NPN/PNP open collector DC30Ｖ 100ｍA ｍax.（Residual voltage 1.8Ｖ ｍax）
Light ON / Dark ON selectable by wiring
2 rotation voluｍe
-40～70℃ / 35～95%RH
Pin No.
①DC10〜30V
Connect to +V Light ON
②
Connect to 0V Dark ON
③0V
④Control output
◦ Specifications and equipment are subject to
change without any obligations on the part of
manufacture.
◦ For more information, questions and comments
regarding products, please contact us below.
Manufactured and sold by:
600-8815 Kyoto, Shimogyo, Awata Chudoji 91, Japan
TEL.+81-(0)75-325-2920
FAX.+81-(0)75-325-2921
Website : http://www.optex-fa.com
BGS
Middle range
Short range
15～50cｍ
10～30cｍ
2ｍs ｍax.
5% ｍax.
OPTEX FA CO.,LTD.
Advertisement
