INSTALLATION, USE AND MAINTENANCE MANUAL 1. REFERENCE STANDARDS CAST RESIN TRAN Cast resin transformers by Bowers Electricals Ltd, are designed and manufactured in Conformity with the latest IEC standards currently in force (unless specifically agreed otherwise) Directive 2004/108/EC – Installation, Ope Electromagnetic compatibility directive.
8 to 24 hours before unpacking the transformer, so that CONNECTIONS it reaches the temperature of the room. 6.8 – VISUAL INSPECTION Tel: 01773 531531 enquires@bowerselec.co.uk www.bowerselec.co.uk Bowers Electricals Ltd, Heanor Gate Road Telephone: 01773 531531 (24 hou E-mail: enquiries@bow...
Page 9
5 days from the dispatch note, it will be assumed that the transformer delivery was flawless. Installation, Ope Bowers Electricals Ltd cannot be held responsible for any incidents Maintenance M HANDLING taking place during installation or service, unless conducted by us.
Page 10
PUSHING OR PULLING THE COILS AND CONNECTIONS. PUSHING OR PULLING THE COILS AND CONNECTIONS. 1.0 – REFERENCE STANDARDS Bowers Electricals Ltd, Heanor Gate Road, Heanor, Derbyshire DE75 7GX 2.0 – RATING PLATE Telephone: 01773 531531 (24 hours) Fax: 01773 716171 3.0 –...
Page 14
(Figure 10) specially designed to ensure proper air circulation inside each 5.3 – STORAGE It is recommended to use a forced cooling system designed by Bowers Electricals Ltd, (Figure 10) coil of a three- or single-phase transformer. Forced ventilation can be •...
Page 15
INSTALLATION, USE AND MAINTENANCE MANUAL 3.0 – LIST OF COMPONENTS AND ACCESS 4.0 – IMPORTANT NOTICE 5.0 – RECEIVING, HANDLING AND STORIN Bowers Electricals Ltd, Heanor Gate Road, Heanor, Derbyshire DE75 7GX 5.1 – RECEIVING Power range Model Telephone: 01773 531531 (24 hours)
Page 16
HAVE TO BE CONSIDERED A PART UNDER VOLTAGE. have to be considered a part under voltage. 5.3 – STORAGE Bowers Electricals Ltd, Heanor Gate Road, Heanor, Derbyshire DE75 7GX 6.0 – INSTALLATION Telephone: 01773 531531 (24 hours) Fax: 01773 716171 E-mail: enquiries@bowerselec.co.uk...
Page 18
Before energizing the unit, an inspection should be carried out in order to guarantee a proper installation and connection of 6.4.1 – NATURAL / FORCED V the transformer. INSTALLATION ROOM Bowers Electricals Ltd, Heanor Gate Road, Heanor, Derbyshire DE75 7GX Telephone: 01773 531531 (24 hours) Fax: 01773 716171 The following steps must be carefully fulfilled: 6.4.2 –...
Page 19
6.4.1 – NATURAL / FORCED V • LV and MV terminals / ground >= 10 MΩ INSTALLATION ROOM If the measured values are much lower, the transformer must by dried. If necessary please contact Bowers Electricals Lim- 6.4.2 – FORCED VENTILATION ited.
Page 20
• Connect the tapping plates in the most suitable position according to the Tel: 01773 531531 enquires@bowerselec.co.uk www.bowerselec.co.uk feeding voltage; Bowers Electricals Ltd, Heanor Gate Road • Re-connect the transformer to the mains. Telephone: 01773 531531 (24 hou E-mail: enquiries@bow...
6.1 – SITE PREPARATION • Electronic controller for PTC sensors Bowers Electricals Ltd, offer two types of control and protection devices for monitoring of the transformer’s temperature and 6.2 – STANDARD INSTALLATION CO • Electronic controller for PT100 sensors tripping: 6.3 –...
Page 23
Figure 18. CONNECTIONS matic or manual) is set in the menu. The device can display Bowers Electricals Ltd, Heanor Gate Road, Heanor, Derbyshire DE75 7GX 6.8 – VISUAL INSPECTION Bowers Electricals Ltd, Heanor Gate Road, Heanor, Derbyshire DE75 7GX...
The surge arresters characteristics depend on the transformer insulation level and the parameters of the distribution system. CONNECTIONS 6.8 – VISUAL INSPECTION Tel: 01773 531531 enquires@bowerselec.co.uk www.bowerselec.co.uk Bowers Electricals Ltd, Heanor Gate Road Telephone: 01773 531531 (24 hou E-mail: enquiries@bow...
Page 27
The Manufacturer is not responsible for the installation of the transformer. Whilst Bowers Electricals Ltd, are NOT responsible for the installation of the transformer, If a problem persists or is not Some possible problems are listed in Table 10 with suggested solutions. If 1.0 –...
Need help?
Do you have a question about the PWAP125 and is the answer not in the manual?
Questions and answers