Advertisement

®
T° HOLD
OPERATORS MANUAL
Medical Solutions, Inc.
3901 Centerview Drive, Suite L, Chantilly, VA 20151
(800) 435-7600 Phone • (703) 834-0039 Fax • www.warmiv.com
6056 Rev B
3/4/09

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T HOLD 1000LS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for MSI T HOLD 1000LS

  • Page 1 ® T° HOLD OPERATORS MANUAL Medical Solutions, Inc. 3901 Centerview Drive, Suite L, Chantilly, VA 20151 (800) 435-7600 Phone • (703) 834-0039 Fax • www.warmiv.com 6056 Rev B 3/4/09...
  • Page 2: Table Of Contents

    T A B L E O F C O N T E N T S Intended Use......................3 Product Description ....................3 2.1 Important Labels and Directions ..............4 2.2 Important Labels Heater Plate and Power Box..........5 Specifications and Operating Information............6 3.1 Specifications....................
  • Page 3 T A B L E O F F I G U R E S Figure 1 - General Set-up ....................3 Figure 2 - Product Labels (Heater Plate) ..............4 Figure 2A (Front)……………………………………………………………….4 Figure 2B (Back) ……………………………………………………………….4 Figure 2C (Side Bottom & Upper Left) ……………………………………….4 Figure 3 - Product Labels (Power Box).................5 Figure 3A (Front)......................5 Figure 3B (Back)......................5...
  • Page 4: Intended Use

    System, helps reduce complications due to inadvertent hypothermia and increases patient safety and comfort. The MSI Fluid Warming System helps keep the patient warm from admission to discharge. We hope that both you and your patients enjoy the benefits of this exclusive technology.
  • Page 5: Important Labels And Directions

    Important Labels and Directions ® The following labels are found on the T° HOLD o Model/ Serial Number. o Do Not Open. o Electrical Shock Symbol. o United States Patents. o Made in the USA. o Warning: Risk of Fire. Replace Fuse as Marked: 250V 2.0 AMP. o Caution: Electrical shock hazard.
  • Page 6: Important Labels Heater Plate And Power Box

    Important Labels Heater Plate and Power Box Label- Label- “Verify “Not Intended Temperature” for Blood or Blood Products” Label- “Risk of Fire” Figure 3A - Front Label- “Electrical Shock Label- Symbol” “Made in the USA” Label- Label- “UL and/or “United States MET Listing”...
  • Page 7: Specifications And Operating Information

    SPECIFICATIONS AND OPERATING INFORMATION Specifications Classification Class 1 Dimensions: Power Box 10.00˝ tall x 6.50˝ wide x 3.00˝ deep Heater Plate 14.25˝ tall x 5.00˝ wide x 1.125˝ deep Heater Plate Capacity 1000 mL Industry standard IV fluid bags. Hook for I.V. Pole Mounting: Heater Plate I.V.
  • Page 8: Operating Instructions

    OPERATING INSTRUCTIONS ® 1. Remove the T° HOLD Heater Plate from its packaging. 2. Check the Heater Plate to ensure that all of the packaging material is removed. 3. Mount the Power Box to the I.V. pole support using the supplied C-Clamp.(Ref: Fig 4) 4.
  • Page 9: Cleaning Instructions

    7. Pull the elastic strap across the fluid bag and secure by affixing the I.V. Bag Strap. 8. Turn the unit “on” by pressing the Power Switch. The switch and the LED indicators on the bottom of the Heater Plate will illuminate when energized. (Ref: Figure 1). If fluid spills inside the Heater Plate or Power Box, unplug the unit to prevent an electrical shock hazard and refer to the Cleaning Instructions (Section 5.0).
  • Page 10: Preventive Maintenance Plan

    PREVENTIVE MAINTENANCE PLAN ® The T° HOLD temperature controller should be verified once every five (5) years). The following items are needed to accurately measure the bag temperature for verification: o Fluke 51 II Digital Thermometer. o 6.00˝ long .093˝ Diameter Type T Needle Thermocouple calibrated to the Thermometer.
  • Page 11: Electrical Schematic

    ELECTRICAL SCHEMATIC FIGURE 7- ELECTRICAL SCHEMATIC 6056 Rev B...
  • Page 12: Appendix A: Limited Warranty

    To enable MSI to administer the Warranty properly, Buyer shall (1) register the Warranty using the form provided below within thirty days of receipt of Equipment, and (2) promptly notify MSI of any claim hereunder. As a condition to the Warranty, Buyer shall use and maintain the Equipment according to the provisions of the Operators Manual.
  • Page 13: Warranty Registration Card

    Phone: Email: Date Purchased: Serial Number: Department Purchased For: COPY THIS PAGE AND MAIL, FAX, OR EMAIL TO: Medical Solutions, Inc. ATTN: Warranty Supervisor 3901 Centerview Drive, Suite L Chantilly, VA 20151 FAX NUMBER: 703-834-0039 EMAIL: msi-warranties@warmiv.com 6056 Rev B...
  • Page 14: Appendix B: Product Labels List

    A P P E N D I X B : P R O D U C T L A B E L S L I S T Label: Electric Shock Symbol Label: UL and/or MET Listing Location: Back of Heater Plate, Back of Location: Back of Heater Plate &...
  • Page 15 Label: Do Not Open Label: Fuse Location: Left Upper & Bottom Front Location: Bottom Side of Power Box of Heater Plate Label: Verify Temperature Label: Ground Location: Front Bottom of Power Box Location: Inside Power Box & Inside Heater Plate Label: Ground Reliability Location: Back of Power Box Labels: Electrical Shock Hazard &...

Table of Contents