Siemens LC37I Series User Manual And Installation Instructions page 7

6.5 Switching off intensive mode
Slide your finger to the left over the settings area
▶
⁠ .
6.6 Switching on the boost function
The boost function is a short-term maximum power set-
ting which can be activated in any fan setting.
Press ⁠ .
▶
a After approx. 20 seconds, the fan automatically
switches back to the fan setting that was previously
set.
6.7 Switching on the fan run-on
During the fan run-on, the appliance continues to run
for a short time and then switches off automatically.
Note: If the intensive mode is activated, the fan run-on
cannot be switched on.
Press until appears on the display.
▶
a The fan run-on starts at fan setting 1.
a The appliance switches off automatically after ap-
prox. 10 minutes.
6.8 Switching off the fan run-on
Slide your finger to the right over the settings area
▶
⁠ .
6.9 Switching on automatic mode
The optimum fan setting is set automatically using a
sensor.
Press ⁠ .
▶
6.10 Switching off automatic mode
Press ⁠ .
▶
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
6.11 Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes. De-
pending on the setting of the sensor sensitivity, the op-
timum fan setting is automatically switched on. If the
sensor control system reacts too weakly or too
strongly, the setting for the sensor sensitivity may
change.
¡ Factory setting: 3
¡ Lowest setting: 1
¡ Highest setting: 5
6.12 Setting the sensor control
Requirement: The appliance is switched off.
Press and hold ⁠ .
1.
a The setting is displayed after approx. one second.
Slide your finger over the settings area
2.
1
Depending on the appliance specifications
Release
3.
6.13 Switching on the lighting
The lighting can be switched on and off independently
of the ventilation system.
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
Press
▶
6.14 Setting the brightness
Press and hold
▶
reached.
6.15 Switching on emotionLight Pro
You can switch on the emotionLight Pro independently
of the ventilation system.
Press
▶
6.16 emotionLight Pro
brightness
Press and hold
▶
reached.
6.17 emotionLight Pro
colour
Requirement: The appliance is switched off.
1. Press
Press
2.
set.
6.18 Setting the PowerBoost position
On some appliances, the filter cover can be adjusted to
an intermediate position. The intermediate position can
be used to eliminate particularly strong cooking smells
and large amounts of steam.
Take hold of the filter cover in the centre and open it
▶
carefully.
6.19 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off,
pears in the display for the grease filter.
¡ After the appliance has been switched off,
pears in the display for the odour filter.
Slide your finger to the left over the settings area
▶
⁠ .
a The saturation indicator is reset.
6.20 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
⁠ .
Requirement: The appliance is switched off.
to save the setting.
⁠ .
until the required brightness is
⁠ .
1
- Setting the
until the required brightness is
1
- adjusting the
⁠ .
or repeatedly until the required colour is
Basic operation en
1
ap-
ap-
7