Subscribe to Our Youtube Channel
Summary of Contents for Maguire Products FLEXBUS
- Page 1 MAGUIRE PRODUCTS INC. FLEXBUS / FLEXBUS Lite FLEXBUS FLEXBUS Lite RECEIVER CONTROL SYSTEM INSTRUCTION MANUAL Original Instructions Manual Copyright Maguire Products, Inc. 2020 Revision Date: January 31, 2020...
- Page 2 M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C .
- Page 3 The information contained within this manual including any translations thereof, is the property of Maguire Products Inc. and may not be reproduced, or transmitted in any form or by any means without the express written consent of Maguire Products Inc.
-
Page 4: Table Of Contents
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Maguire Products Inc. MAGUIRE Flexbus / Flexbus Lite Table of Contents... -
Page 5: Flexbus Overview
Install a single wire and conveniently located drops to connect the control to all receivers and pumps. System Grows with Your Needs Each Flexbus central control allows addition of up to 5 pumps and up to 24 receivers per pump for a total of 120 receivers. Flexbus Lite Included within the Maguire Weigh Scale Blender Touchscreen, Flexbus Lite enables local control of a single pump and up to 9 receivers. -
Page 6: Flexbus Home Screen
Flexbus uses a MAC address to individually identify each Flexbus pump and receiver. Identification and numeric assignment of each Flexbus pump and receiver is setup within the Flexbus controller through the order that the pump or receiver is turned on and discovered during the Pump Assignment routine and the Receiver Assignment routine setup processes. - Page 7 Enabling Flexbus Lite in the Weigh Scale Blender Touchscreen Controller Flexbus Lite is an option that can be enabled within the Weigh Scale 4088 Touchscreen controller allowing local control of a single pump and up to 9 receivers. Additional components are required for blender loading including receivers equipped with Flexbus, a T-drop, a position hub, pump module, and necessary cabling.
- Page 8 Pumps Event Log and Alarm History Flexbus Firmware Information Setup Enters password protected setup screens. Flexbus System Setup Options Note: Pumps must be assigned before Receivers. Note: Flexbus Lite uses a single pump and up to 9 receivers.
-
Page 9: Flexbus Pump Assignment
Flexbus Lite (part of the Maguire 4088 TS Weigh Scale Blender) controls a single pump. The Flexbus System can control of to 5 pumps. If you have two or more pumps (Flexbus only), turn OFF all pumps prior to running Setup in the Flexbus controller, otherwise: To assign Pumps,... - Page 10 M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . While in the Setup screen you can go straight to setting up Receivers without re-entering the password.
-
Page 11: Receiver Assignment
The gray screen contains any previously assigned Receivers. For first time setup, this screen is probably blank and no Receivers have been assigned. Turn on your Flexbus Receivers in the order that you want then to be assigned. -
Page 12: Receiver Configuration
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Receiver Configuration The Receiver configuration screen is accessible from the Home screen. Pressing a... - Page 13 M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Load Retry - The number of times the receiver will try to successfully load material and satisfy the sensor.
-
Page 14: Pump Configuration
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Pump Configuration Pressing the pump button in the right navigation takes you to the Pump overview screen and then pressing a pump in this overview screen will open the Pump's Configuration screen. - Page 15 M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Pump Configuration Fields Blowback - Blowback is a pulse of air to clear the filter. Blowback has two configuration fields.
-
Page 16: Removing Receivers Or Pumps
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Removing Receivers or Pumps from the configuration If a pump or receiver needs to be removed from the configuration, it can be removed using this procedure. -
Page 17: Flexbus System Setup Options
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Flexbus System Setup Options The Setup screen also allows for setting: Date and time, screensaver timeout,... - Page 18 22. Press the green check when complete. TCP/IP Configuration Enter the IP address for the Flexbus controller for Modbus TCP communications. MAC address is provided on-screen for DHCP. See the Maguire Modbus Register Mapping document for more information.
-
Page 19: Flexbus Main Screen Details
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Flexbus Controller Main Screen Details Live Status Panel Navigation Menu Displays the live status of all receivers. - Page 20 M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . What the Receiver Symbols Represent: Receiver is online and idle. Lost communication with receiver.
-
Page 21: Event And Alarm Logging
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Event and Alarm Logging On the main screen is the Event and Alarm button. Pressing this button will display the Event and Alarm Log. -
Page 22: Flexbus Wiring Diagrams
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Flexbus Wiring Diagrams... - Page 23 M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C .
-
Page 24: Flexbus Component Map
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Flexbus Component Map... -
Page 25: Flexbus Lite Component Map
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Flexbus Lite Component Map... - Page 26 M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C .
- Page 27 M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C .
-
Page 28: Warranty
This warranty shall not apply to any Flexbus System which has been repaired or altered outside MAGUIRE PRODUCTS factory, unless such repair or alteration was, in our judgment, not responsible for the failure;... -
Page 29: Technical Support And Contact Information
M A G U I R E FLEXBUS™ M A G U I R E P R O D U C T S , I N C . Technical Support and Contact Information Maguire Products Inc. 11 Crozerville Road...
Need help?
Do you have a question about the FLEXBUS and is the answer not in the manual?
Questions and answers