Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for KAR-TECH MCT245
- Page 1 MCT245 2.4GHz RECEIVER OEM INSTALLATION AND OPERATION MANUAL June 27, 2020...
-
Page 2: Table Of Contents
MCT245 RECEIVER INDEX DESCRIPTION ................2 OPERATION ................2 INSTALLATION ................. 4 BEFORE APPLYING POWER! ............5 TROUBLESHOOTING ..............6 TRANSCEIVER PICTORIAL ............7 SPECIFICATIONS ..............7 INSTRUCTION TO THE USER ............. 8 INDUSTRY CANADA STATEMENTS ........... 10... -
Page 3: Description
MCT245 transceiver. RF processor and then to RF circuit, then The MCT245 is not designed for antenna. The microcontroller is multiple antenna applications responsible for the control of should used entire communication. - Page 4 MCT245 RECEIVER circuitry. The RF section runs on construction equipment, the 3.3V supply. other similar equipment. MCT245 uses Frequency Hopping Spread Spectrum channels for that uses mode, between 2.407GHZ and 2.470GHZ, with 1MHZ resolution. receivers matched to the transmitters to use the...
-
Page 5: Installation
MCT245 RECEIVER INSTALLATION 1) Attach the external harness to the MCT245. 2) Assemble MCT245 assembly into Enclosure. 3) Place a label on the outside of the enclosure on the side. On the label, include following: “FCC P4U- MCT245” “IC: 4534A- MCT245, CE”... -
Page 6: Before Applying Power
2.1091 for definitions of separation distance of mobile fixed at least 20cm from all applications. person and not be co- D) Do not operate the MCT245 located with any other without an antenna. transmitters except in E) Documentations: accordance with FCC host’s... -
Page 7: Troubleshooting
MCT245 RECEIVER Read the rest of this manual. TROUBLESHOOTING There are no user serviceable parts in the MCT245 Receiver. Contact your KAR-TECH representative further instructions or servicing. PARTS LIST PART NUMBER DESCRIPTION 022081A MCT245 RADIO TRANSCEIVER – REMOVEABLE ANTENNA There are no user-serviceable parts inside the transmitter or the receiver. -
Page 8: Transceiver Pictorial
MCT245 RECEIVER SPECIFICATIONS Equipment Class ......Part 15 Spread Spectrum Transmitter FCC ID ................P4U- MCT245 ICC (Industry Canada Certification) ID ......4534A- MCT245 TRANSCEIVER Power supply ................. 9-30VDC Operating Current ................ 48mA Operating temperature - Radio ........-40˚C to +85˚C Storage temperature ........... -
Page 9: Instruction To The User
MCT245 RECEIVER INSTRUCTION TO THE USER This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 10 This exterior label can use wording such as the following: “Contains Transmitter product FCC ID: P4U- MCT245 ” When the product is installed inside another device, the user manual of this device must contain below warning statements;...
-
Page 11: Industry Canada Statements
MCT245 RECEIVER INDUSTRY CANADA STATEMENTS This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. - Page 12 If the IC number is not visible when the product is installed inside another device, then the outside of the device into which the product is installed must also display a label referring to the enclosed product. This exterior label can use wording such as the following: “Contains IC: 4534A- MCT245 ”...
- Page 13 MCT245 RECEIVER When the product is installed inside another device, the user manual of this device must contain below warning statements: 1. This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
- Page 14 The ‘CE’ mark must be placed on the OEM product per the labeling requirements on the Directive. Declaration of Conformity (DOC) This DOC can be downloaded from the www.kar-tech.com. The device complies with RF specifications when the device used at your body.