1.1 Product Description a) Type of EUT : 802.11b mini-pci wireless lan card b) Trade Name : Quanta c) Model No. : WM1 d) Power Supply : Adaptor:I/P:100~240Vac 50/60Hz; O/P:3.3V, Tx:380MA, Rx:215MA, Tx:1.245W, Rx:0.7095W 1.2 Characteristics of Device w Fully IEEE 802.11b and Wi-Fi compatible w Seamless roaming under 802.11b WLAN intrastructure...
ETC Report No. : ET90S-11-032 Sheet 2 of 104 Sheets FCC ID. : HFSWM100 2 PROVISIONS APPLICABLE 2.1 Definition Unintentional radiator: A device that intentionally generates and radio frequency energy for use within the device, or that sends radio frequency signals by conduction to associated equipment via connecting wiring, but which is not intended to emit RF energy by radiation or induction.
ETC Report No. : ET90S-11-032 Sheet 3 of 104 Sheets FCC ID. : HFSWM100 2.2 Requirement for Compliance (1) Conducted Emission Requirement For unintentional device, according to 15.107(a) Line Conducted Emission Limits is as following: Frequency Emissions Emissions 0.45 - 30.0 48.0 For intentional device, according to 15.207(a) Line Conducted Emission Limits is same as above table.
Page 8
ETC Report No. : ET90S-11-032 Sheet 4 of 104 Sheets FCC ID. : HFSWM100 (4) Bandwidth Requirement For direct sequence system, according to 15.247(a)(2), the minimum 6dB bandwidth shall be at least 500 kHz. (5) Output Power Requirement For direct sequence system, according to 15.247(b), the maximum peak output power of the transmitter shall not exceed 1 Watt.
ETC Report No. : ET90S-11-032 Sheet 6 of 104 Sheets FCC ID. : HFSWM100 2.5 User Information The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
ETC Report No. : ET90S-11-032 Sheet 7 of 104 Sheets FCC ID. : HFSWM100 3. SYSTEM TEST CONFIGURATION 3.1 Justification For both radiated and conducted emissions, EUT was extended from notebook PC. The notebook PC put in an aluminum box and shielded it. 3.2 Devices for Tested System Device Manufacture...
ETC Report No. : ET90S-11-032 Sheet 8 of 104 Sheets FCC ID. : HFSWM100 4 RADIATED EMISSION MEASUREMENT 4.1 Applicable Standard For unintentional radiator, the radiated emission shall comply with 15.109(a). For intentional radiators, according to 15.247 (a), operation under this provision is limited to frequency hopping and direct sequence spread spectrum, and the out band emission shall be comply with 15.247 (c) 4.2 Measurement Procedure...
ETC Report No. : ET90S-11-032 Sheet 10 of 104 Sheets FCC ID. : HFSWM100 4.3 Measuring Instrument The following instrument are used for radiated emissions measurement : Equipment Manufacturer Model No. Next Cal. Due EMI Test Receiver Hewlett-Packard 8546A 01/31/2002 Horn Antenna EMCO 3115...
ETC Report No. : ET90S-11-032 Sheet 11 of 104 Sheets FCC ID. : HFSWM100 4.4 Radiated Emission Data 4.4.1 RF Portion a) Channel 1 Operation Mode : Receiving /Transmitting Fundamental Frequency : 2412 MHz ( Local Frequency : 2038 MHz ) Test Date : Dec.
Page 16
ETC Report No. : ET90S-11-032 Sheet 12 of 104 Sheets FCC ID. : HFSWM100 b) Channel 6 Operation Mode : Receiving / Transmitting Fundamental Frequency : 2437 MHz ( Local Frequency : 2063 MHz ) Test Date : Dec. 03, 2001 Temperature : 23 Humidity : 65 % Frequency...
Page 17
ETC Report No. : ET90S-11-032 Sheet 13 of 104 Sheets FCC ID. : HFSWM100 c) Channel 11 Operation Mode : Receiving / Transmitting Fundamental Frequency : 2462 MHz ( Local Frequency : 2088 MHz ) Test Date : Dec. 03, 2001 Temperature : 23 Humidity : 65 % Frequency...
ETC Report No. : ET90S-11-032 Sheet 14 of 104 Sheets FCC ID. : HFSWM100 4.4.2 Other Emission a) Emission frequencies below 1 GHz Test Date : Dec. 05, 2001 Temperature : 23 Humidity : 65 % Frequency Ant-Pol Meter Corrected Result Limit Margin...
ETC Report No. : ET90S-11-032 Sheet 19 of 104 Sheets FCC ID. : HFSWM100 5 CONDUCTED EMISSION MEASUREMENT 5.1 Standard Applicable For unintentional and intentional device, Line Conducted Emission Limits are in accordance to 15.107(a) and 15.207(a) respectively. Both Limits are identical specification. 5.2 Measurement Procedure 1.
ETC Report No. : ET90S-11-032 Sheet 22 of 104 Sheets FCC ID. : HFSWM100 5.5 Conducted Measurement Equipment The following test equipment are used during the conducted test . Equipment Manufacturer Model No. Next Cal. Due RF Test Receiver Rohde and Schwarz ESCS30 09/18/2002 Line Impedance...
ETC Report No. : ET90S-11-032 Sheet 24 of 104 Sheets FCC ID. : HFSWM100 6 ANTENNA REQUIREMENT 6.1 Standard Applicable For intentional device, according to 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device.
ETC Report No. : ET90S-11-032 Sheet 25 of 104 Sheets FCC ID. : HFSWM100 7 EMISSION BANDWIDTH MEASUREMENT 7.1 Standard Applicable According to 15.247(a)(2), for direct sequence system, the minimum 6dB bandwidth shall be at least 500 kHz. 7.2 Measurement Procedure 1.
ETC Report No. : ET90S-11-032 Sheet 27 of 104 Sheets FCC ID. : HFSWM100 8 OUTPUT POWER MEASUREMENT 8.1 Standard Applicable For direct sequence system, according to 15.247(b), the maximum peak output power of the transmitter shall not exceed 1 Watt. If transmitting antennas of directional gain greater than 6 dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6 dBi.
ETC Report No. : ET90S-11-032 Sheet 28 of 104 Sheets FCC ID. : HFSWM100 8.4 Measurement Data Test Date : Dec. 04, 2001 Temperature : 20 Humidity: 65 % Channel 01 : Output Peak Power is 19.9 dBm or 97.7 mW Channel 06 : Output Peak Power is 19.8 dBm or 95.5 mW Channel 11 : Output Peak Power is 19.3 dBm or 85.1 mW Note: Please see Appendix 4 for ploted datas...
ETC Report No. : ET90S-11-032 Sheet 29 of 104 Sheets FCC ID. : HFSWM100 9 100 kHz BANDWIDTH OF BAND EDGES MEASUREMENT 9.1 Standard Applicable According to 15.247(c), if any 100 kHz bandwidth outside these frequency bands, the radio frequency power that is produced by the modulation products of the spreading sequence, the information sequence and the carrier frequency shall be either at least 20 dB below that in any 100 kHz bandwidth within the band that contains the highest level of the desired power or shall not exceed the general levels specified in 15.209(a),...
ETC Report No. : ET90S-11-032 Sheet 30 of 104 Sheets FCC ID. : HFSWM100 9.4 Measurement Data Test Date : Dec. 04, 2001 Temperature : 20 Humidity: 65 % Lower Band Edge : maximum value is –26.0 dBm that is attenuated more than 20dB Upper Band Edge : maximum value is –48.7 dBm that is attenuated more than 20dB Note: Please see Appendix 5 for ploted datas Rev.
ETC Report No. : ET90S-11-032 Sheet 31 of 104 Sheets FCC ID. : HFSWM100 10 POWER DENSITY MEASUREMENT 10.1 Standard Applicable According to 15.247(d), for direct sequence systems, the transmitted power density averaged over any 1 second interval shall not be greater than 8 dBm in any 3 kHz bandwidth within these bands.
ETC Report No. : ET90S-11-032 Sheet 32 of 104 Sheets FCC ID. : HFSWM100 10.4 Measurement Data Test Date : Dec. 04, 2001 Temperature : 20 Humidity: 65 % Channel 01 : Maximun Power Density of 3 kHz Bandwidth is –8.7 dBm Channel 06 : Maximun Power Density of 3 kHz Bandwidth is –8.5 dBm Channel 11 : Maximun Power Density of 3 kHz Bandwidth is –9.3 dBm Note: Please see Appendix 6 for ploted datas...
ETC Report No. : ET90S-11-032 Sheet 33 of 104 Sheets FCC ID. : HFSWM100 11 PROCESSING GAIN MEASUREMENT 11.1 Standard Applicable According to 15.247(e), the processing gain of a direct sequence system shall be at least 10 dB. The processing gain shall be determined from the ratio in dB of the signal to noise ratio with the system spreading code turned off to the signal to noise ratio with the system spreading code turned on, as measured at the demodulated output of the receiver.
Page 38
ETC Report No. : ET90S-11-032 Sheet 34 of 104 Sheets FCC ID. : HFSWM100 (3) Test Results The tested data are listed in the following pages. After discarding the worst 20% of the J/S ratio data points, the lowest remaining J/S ratio is used to determine the processing gain (PG), according to the derivative equation (4/2), of each tested channel.
Need help?
Do you have a question about the WM1 and is the answer not in the manual?
Questions and answers