Subscribe to Our Youtube Channel
Summary of Contents for Trophy AMD-53-S2
- Page 1 AMD-53-S2 MODULATOR / MULTIPLEXER AMD-53-S2 DVB-S2 MODULATOR / 120-CHANNEL MULTIPLEXER Part No. 1001-1008 Instruction Manual INSTRUCTION MANUAL...
-
Page 2: Table Of Contents
AMD-53-S2 MODULATOR / MULTIPLEXER TABLE OF CONTENTS 1. GENERAL INFORMATION 1.1. MAIN FUNCTIONS OF AMD-53-S2 MODULATOR / MULTIPLEXER 2. TROPHY-ACCESS CAS 3. INSTALLING AND OPERATING INSTRUCTIONS 3.1. SAFETY INSTRUCTIONS 3.2. GENERAL DESCRIPTION OF FUNCTIONS 3.3. MULTIPLEXER/REMULTIPLEXER/PID FILTER 3.4. INSTALLING FUNCTIONAL ELEMENTS AND FACTORY SETTINGS 3.5. -
Page 3: General Information
DVB signals in full HD resolution. The device receives a data stream via Gigabit Ethernet or ASI (optionaly). It can receive up to 120 transport streams from the TROPHY HeadEnd or from another IP sources included MPEG transport streams. - Page 4 AMD-53-S2 MODULATOR / MULTIPLEXER integrates the core technology required to perform high quality modulation based on TROPHY expertise. It provides customers with a best in class performance, providing a high SNR value, excellent shoulder levels and lowest phase noise.
- Page 5 (named Cardsharing). Scrambler is performed within the hardware of the AMD-53-S2 DVB-S2 MODULATOR/MUX. The Billing server provides office. The decoder automatically switches off at a zero balance in the subscriber account number. Billing data are fed to the AMD-53-S2 MODULATOR/MUX over Ethernet or ASI. Options Cardless, doesn’t match CSA algorithm...
-
Page 6: Trophy-Access Cas
PMT, SDT and TDT). 3.3. MULTIPLEXER/REMULTIPLEXER/PID FILTER A multiplexer has been integrated into the AMD-53-S2 device for processing the incoming transport streams. On condition that in these transport streams an adequate transmission rate is available, or additional transport volume is achievable by raising the transport streams bit rate, new services and/ or program components can be added. -
Page 7: Installing Functional Elements And Factory Settings
AMD-53-S2 MODULATOR / MULTIPLEXER 3.4. INSTALLING FUNCTIONAL ELEMENTS AND FACTORY SETTINGS Explanation of the functional elements: Power (green LEDs scale) Switched ON, 30 sec after power restart Input stream + WEB interface Ethernet RJ-45, 10/100/1000, UDP L-band output N-type connector... -
Page 8: Settings For The Ethernet Network Interface
AMD-53-S2 MODULATOR / MULTIPLEXER 3.5. SETTINGS FOR THE ETHERNET NETWORK INTERFACE Allocation of IP address, default : 10.10.10.20 One-time at the start an IP address via a DHCP server is requested. If the probe fails, will use the default IP address. -
Page 9: Configurations Via The Ethernet Interface
BACKUP. You can save all settings of the device as a backup.json file. RESTORE. You can upload a backup.json file to change the device configuration. ADD KEY. You have the opportunity to make an additional order for the TROPHY-ACCESS license. The received key must be entered after pressing the ADD KEY button. - Page 10 BILLING SERVER address can be specified if a TROPHY-ACCESS scrambled signal is at the modulator/multiplexer output. In this case, the subscription information (list of included decoders and rights to view of program packages) should be present in the stream.
-
Page 11: Inputs
AMD-53-S2 MODULATOR / MULTIPLEXER 3.8. INPUTS The 120 possible logical stream channels can be defined as a multi-program stream or single program stream and can be operated according to the IP address space specified in multicast mode or unicast. In the first step, the IP address, netmask and gateway address of stream sources are assigned to the ETHERNET interface for use in the local network. - Page 12 AMD-53-S2 MODULATOR / MULTIPLEXER 3.8.2. IP-˃MUX mode (with DEMUX/MUX processing). The data enters the modulator via preliminary processing. In this mode, data is received from one or several ports. Unicast packets receiving Multicast packets receiving INSTRUCTION MANUAL...
-
Page 13: Programs
AMD-53-S2 MODULATOR / MULTIPLEXER 3.9. PROGRAMS Program name: The program name is the service designation. By default, for each program, the program name will be automatically generated, which coincides with the name specified in the incoming thread. You can change the name to another one. -
Page 14: Generator
AMD-53-S2 MODULATOR / MULTIPLEXER 3.10. SI GENERATOR Service information is a special set of elementary streams that contain a set of database tables describing the structure of transport stream, the services within it and some useful information that digital TV receivers can show the user, such as the name of the service and schedule information for the services. -
Page 15: Modulator Parameters
Payload rate: 30,155 Mbit (0,94%) Subs rate: 0 Mb Free capacity is filled with subscription packages if the billing server sends TROPHY-ACCESS CAS data to the modulator. The efficiency of data transmission is maximum. The capacity that the subscription data occupies is indicated in the form of a yellow scale. Thanks to this technology, the CAS data transmission efficiency is maximum. -
Page 16: Specifications
AMD-53-S2 MODULATOR / MULTIPLEXER 4. SPECIFICATIONS Standards Carrier ID ETSI 103 129 DVB-S2 EN 302 307 MPEG-TS EN 301 210 DVB MPEG-TS over ASI EN50083-9; ETSI TR 101 891 DVB MPEG-TS over IP ETSI TS 102 034 MPEG-2 PSI Tables (PAT&PMT) - Page 17 AMD-53-S2 MODULATOR / MULTIPLEXER Multiplexer Quantity of multiplexed channels up to 120 PID quantity supported All PIDs of input sevices Modulation DVB-S2 QPSK: 1/3, 2/5, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10 8PSK: 3/5, 2/3, 3/4, 5/6, 8/9, 9/10...
Need help?
Do you have a question about the AMD-53-S2 and is the answer not in the manual?
Questions and answers