1. Manuals
  2. Brands
  3. Steiner Manuals
  4. Snow Blower
  5. 75-71215B4
  6. Operations & parts manual

Steiner 75-71215B4 Operations & Parts Manual

450 cab kit
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MODEL:
75-71215B
450 CAB KIT
www.steinerturf.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 75-71215B4 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Steiner 75-71215B4

Summary of Contents for Steiner 75-71215B4

  • Page 1 MODEL: 75-71215B 450 CAB KIT www.steinerturf.com...
  • Page 2 CALIFORNIA WARNING Proposition 65 Warning The engine exhaust from this product Diesel engine exhaust and some of contains chemicals known to the State its constituents are known to the State of California to cause cancer, birth of California to cause cancer, birth defects or other reproductive harm.

  • Page 3: Table Of Contents

    IMPORTANT MESSAGE Thank you for purchasing this Schiller Grounds Care, Inc. product. You have purchased a world class product, one of the best designed and built anywhere. This machine comes with an Owner / Operator's Manual and an Illustrated Parts Manual. The useful life and good service you receive from this machine depends to a large extent on how well you read and understand these manuals.

  • Page 4: Safety

    SAFETY NOTICE !!! This symbol means: ATTENTION! Unauthorized modifi cations may present extreme BECOME ALERT! safety hazards to operators and bystanders and could also result in product damage. Your safety and the safety of others is involved. Schiller Grounds Care, Inc. strongly warns against, rejects and disclaims any modifi cations, add-on Signal word defi...

  • Page 5: Assembly

    ASSEMBLY Read these instructions and identify all com- FIGURE 1 ponents. Please retain these instructions for future reference and parts ordering information. MACHINE PREPARATION 1. Remove all attachments if present. 2. With the engine off, disconnect the battery using the battery main disconnect switch on the back of the battery compartment.
  • Page 6 ASSEMBLY FRONT MOUNT INSTALLATION: 5. Secure the two front mount brackets (Item 7) to the bottom of the machine using hardware. Torque to 70 ft-lb (95n-m). Figure 4 (2) 1/2" X 1.50" long bolts (Item 16) (2) 1/2" nylon nuts (Item 17) (3) 1/2" large OD flat washers (Item 31) two on right side one on outside left side (1) 1/2" small OD flat washer (Item 15)
  • Page 7 ASSEMBLY 10. On the inside of the removed pump cover, install the top filler plate (Item 5) using two .25 x .75 screws (Item 27) and two locking nuts. (Item 23) Install the screws from the outside inward. Figure 7 11. Install the filler dash bottom (Item 4) using two .25 x .75 screws (Item 27) and two locking nuts (Item 23).
  • Page 8 ASSEMBLY 14. Install the RH dash filler mounting bracket (Item 9) using two .25 x .75 screws (Item 27) Bracket should sit on top of the hood rail with hardware going through hood then into bracket. Figure 10 If you don't have enough room, you may have to rotate the hydraulic cooler hose on the oil cooler inward and upward (clockwise) towards the cen- ter of the machine.
  • Page 9 ASSEMBLY REAR MOUNT INSTALLATION: FIGURE 14 FIGURE 13 17. Loosely secure the Rear Mounting Bracket (Item 6) to the machine as shown in Figure 13 & 14 using hardware: (2) 1/2" U-bolts (Item 25) (4) 1/2" serrated flange nuts (Item 22) DO NOT TIGHTEN AT THIS TIME! INSTALLING THE CAB: 18.
  • Page 10 ASSEMBLY 21. Install the rubber isolators (Item 28) onto the rear mount bracket. Secure the rear mounting bracket to the back of the cab using hardware: Figure 17 (4) 3/8" X 2.50" long bolt (Item 14) (4) 3/8" nylock nuts (Item 29) (4) 3/8" flat washers (Item 30) Torque to 30 ft-lb (41 N-m) 22.
  • Page 11 ASSEMBLY 25. Remove black plug from the 5/16" hole in the FIGURE 21 middle top of the instrument panel. Install the bungee cord guide (Item 2) with one screw (Item 20) and flange nut (Item 23). Figure 21 & 22 ELECTRIC HOOK-UP: 26. Locate main harness secured to the front left cab tube.
  • Page 12 ASSEMBLY 34. Coil excess wire harness and secure using FIGURE 25 nylon ties. Make sure to leave enough room for complete front travel of machine. Avoid any HOT or MOVING parts. DO NOT SECURE WIRE HARNESS TO HIGH PRESSURE FUEL LINES! 35.
  • Page 13 PARTS SECTION...

  • Page 14: Mounting Kit Assembly

    MOUNTING ASSEMBLY FIGURE 1 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4175238-4 ASSY, FILLER, DASH LH 4175238-12 STOP, OSCILLATION 4175238-5 ASSY, FILLER, DASH RH 4171878-5 S-SPACER-CORD GUIDE 4175238-6 ASSY, FILLER, DASH FRNT RH 4175238-1 FILLER, LWR FRONT, CNTR 4175238-7 ASSY,BRKT,DASH FILLER LH 4175238-2 FILLER DASH, BOTTOM...

  • Page 15: Kit Hardware

    HARDWARE FIGURE 2 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4171015-96 S-BLT, HHCS .375 X 2.5 4171878-21 S-NUT, FL HEX .25 4171878-20 S-WSHR, .50 TYPE AN 4171015-102 S-BLT, HHCS .75 4171878-16 S-BLT, HHCS .5 X 1.5 4171878-25 S-UBOLT, .5X3X3.5 4171878-18 S-NUT, NYLOCK .5 4171878-19...

  • Page 16: Front View Assembly

    FRONT VIEW ASSY FIGURE 3 RUN CROSS CORD THROUGH THE LOOPS OF THE FRONT CROSS VINYL - DO NOT RUN THE LONG HOOD SEAL CORD THROUGH THE CROSS VINYL LOOPS - RUN THE LONG HOOD SEAL CORD THROUGH SIDE AND LOWER LOOPS OF FRONT VINYL WINDOWS MATCH DRILL .219 HOLES (14)

  • Page 17: Rear View Assembly

    REAR VIEW ASSY FIGURE 4 SEE DETAIL D DETAIL D ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4171015-8 S-MOUNT, TEE HANDLE , RH 4171015-44 S-WINDOW TRIM SEAL, 11/16 11" 1 4171015-41 S-DOOR TRIM SEAL, 11/16 6" 4171015-28 S-WASHER, SHOULDER GLASS 4 4171015-34 S-TRIM SEAL, , 180 DEG 5"...

  • Page 18: Headliner Assembly

    HEADLINER ASSY FIGURE 5 NO NUTSERTS IN TOP (4) HOLES GROUND LOCATION 6 & 5 11 & 12 2 & 4 HOOK UP GROUND FROM BELOW **DO NOT ATTACH OVER THE TOP** SEE DETAIL A (FUSE COVER NOT SHOWN) (7.5 AMP FOR WIPER) (5 AMP FOR DOME LIGHT)

  • Page 19: Wire Harness

    WIRE ASSEMBLY FIGURE 6 GRND STUD BLACK WHITE DOME+ DOME- BLACK ITEM PART NO. DESCRIPTION 4171015-56 HEADLINER HARNESS ASSY 4171015-77 MAIN WIRE HARNESS ASSY...

  • Page 20: Right Side Assembly

    RIGHT SIDE ASSY FIGURE 7 SEE DETAIL G DETAIL A SEE DETAIL A SEE DETAIL E 9.00" - TRIM DETAIL G TO FOLLOW SLOPE DETAIL E...
  • Page 21 RIGHT SIDE ASSY FIGURE 7 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4171015-61 S-GLASS, RH WINDOW 4171015-65 S-GLASS, SIDE UPPER, 4171015-66 S-GLASS, SIDE LOWER, PERED 1 4171015-28 S-WASHER, GLASS MOUNT 4171015-49 S-MSCR, .312-18 NC X 1.50 TH 4171015-35 S-WASHER, .344 X 1.25 4171015-26 S-ROLL PIN, .187 X .50 4171015-33...

  • Page 22: Left Side Assembly

    LEFT SIDE ASSY FIGURE 8 16 & 30 & 32 5 & 4 SEE DETAIL A DETAIL A 14 10 7...
  • Page 23 LEFT SIDE ASSY FIGURE 8 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4171015-12 S-WELDMENT, DOOR, LH 4171015-14 S-WELDMENT, DOOR HINGE 4171015-42 S-LATCH, ROTARY 4171015-64 S-GASKET FOR OVAL 4171015-63 S-HANDLE, PADDLE LOCKING 4171015-81 S-TAB, TRIP 4171015-28 S-WASHER, GLASS MOUNT 4171015-65 S-GLASS, SIDE, UPPER, 4171015-66 S-GLASS, SIDE, LOWER...

  • Page 24: Roof Assembly

    ROOF ASSY FIGURE 9 DETAIL B DETAIL C DETAIL B DETAIL C...
  • Page 25 ROOF ASSY FIGURE 9 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 4171015-80 S-ASSY, ROOF 4171015-82 S-WASHER .3125 4171015-83 S-NUT .3125 4171015-28 S-WASHER, GLASS MOUNT 4171670-07 BLT-TRX HD 5/16-18 X 4-1/4 4171015-35 S-WASHER, .344 X 1.25 4171015-50 S-MSCR.312-18 NC X 1.0 TORX 4171015-36 S-HINGE, GLASS, BLACK 4175238-11...
  • Page 26 SCHILLER GROUNDS CARE, INC. ONE BOB-CAT LANE P.O. BOX 469 JOHNSON CREEK, WI 53038 920-699-2000 www.schillergc.com ©Schiller Grounds Care, Inc. 2010...

Table of Contents