Advertisement
USAUTOMATIC
ELECTRIC GATE LOCK
Part Number 070510
Installation Manual
The USAutomatic Electric Gate Lock works with an automatic gate operator to securely lock the gate into
position without having to get out of your vehicle. The USAutomatic Electric Gate Lock is wired into the gate
operator control box, so that when an input device such as a transmitter or keypad is used to open the gate,
the USAutomatic Electric Gate Lock disengages and the gate will open. When the gate closes, the gate lock
automatically engages to secure the gate in the closed position.
The USAutomatic Electric Gate Lock provides an extra level of protection.
In addition to protection, it provides stability for the gate by securely locking the gate into position, so that
damaging effects, such as wind, are minimized. The result is the gate and automatic gate operator will stay
in excellent working condition for a much longer time.
The USAutomatic Electric Gate Lock Assembly works with most types of gates and mounting applications.
NOTE: In order for the USAutomatic Electric Gate Lock to work properly, the gate must close firmly against
the stop gate post or closed position stop plate. To achieve the desired closed position, you may need to
slightly adjust the gate operator closed limit set points. Instructions for adjusting the closed limit set points
are included in your automatic gate operator manual.
IMPORTANT:
Electric Gate Lock Part Number 070510 Technical Information
Operating Voltage
Nominal Activation Current
Duty Cycle
Construction
Locking Mechanism
Min Recommended Supply Voltage Wire Guage
Emergency Release Type
Installation Type
Periodic Service Recommendation
Temperature Range
Shipping Weight
PLEASE READ THE ENTIRE MANUAL CAREFULLY PRIOR TO INSTALLATION.
THIS LOCK IS DESIGNED FOR 12VDC CONTROL SYSTEMS.
PLEASE NOTE OPERATING VOLTAGE IS 10VDC TO 14VDC
10 vdc to + 14 vdc
< 250 milli amps
Intermittent
Steel Powder Coated Black Housing
Spring Loaded self-latching
18 gauge / .8 mm2
Removable Strike Pin
Bolt or Weld On Brackets
Lightly Grease Strike Pin
-30 C to +85 C
10 lbs / 4.53 kgrams
Advertisement
Table of Contents
Summary of Contents for USAutomatic 070510
- Page 1 The USAutomatic Electric Gate Lock works with an automatic gate operator to securely lock the gate into position without having to get out of your vehicle. The USAutomatic Electric Gate Lock is wired into the gate operator control box, so that when an input device such as a transmitter or keypad is used to open the gate, the USAutomatic Electric Gate Lock disengages and the gate will open.
- Page 2 PARTS INVENTORY Lock Housing 3/8” Lock Nuts Part # 070660 Part # 610502 8 per Lock Mounting Bracket 1/8” Allen Wrench Part # 070670 Part # 610500 Strike Bracket 7/8” Rubber Plugs Part # 070680 Part # 610501 2 per Wire Nut Strike Pin with Clip Part # 620018...
- Page 3 INSTALLATION EXAMPLES These are the basic mounting instructions as there are so many variations in gates, sizes and types. The Electric Lock will adapt to almost any gate installation. HORIZONTAL SWING GATE MOUNT (Horizontal Mounting of Lock on Swing Gate with Pull to Open Swing Gate Opener) Lock Mounted on Swing Gate Wire from lock to gate controller Lock Mounted on Swing Gate Post...
- Page 4 Attach the Green (+) and Blue (-) wires to the wires leading to your gate opener control box. (Fig C) Do not attach wires to operator yet! Disconnect power to opener. On USAutomatic operators, remove motor plug(s) (X1 or X2) from control board. Figure D Mount the Lock.
- Page 5 Fully tighten lock nuts on both brackets. You are now ready to power the lock. Attach the two wires from the electric lock to those leading to the correct terminals on your operator board. (For USAutomatic Figure E openers, see Wiring Chart)
- Page 6 This page intentionally left blank...
- Page 7 If your USAutomatic Electric Gate Lock, also referred to as the “Product”, does not work properly due to a defect in materials or workmanship, USAutomatic will, for the length of 1 year, which begins on the date of the original purchase, at its option either (a) repair your Product with new or refurbished parts, or (b) replace it with a new or refurbished Product.
- Page 8 © USAutomatic, LTD, 2014 rev. A All rights reserved. No part of this may be reproduced by any means without the expressed written consent of the publisher.
Need help?
Do you have a question about the 070510 and is the answer not in the manual?
Questions and answers