Advertisement
WARNING! Wear approved safety eye protection, ear defenders, gauntlets and, if dust is generated, respiratory protection.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
Keep hands and body clear of the worktable when operating the cut-off machine, and DO NOT position your body in line with the blade.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
Avoid subjecting blade to excessive strain, always ease blade down against workpiece (a harsh downward impact may break the blade). Do
not apply undue force on the handle in order to cut workpiece. Maintain a controlled cutting speed through the workpiece.
WARNING! DO NOT switch on the cut-off machine whilst the blade is in contact with the workpiece. Bring the rotating blade to the workpiece.
Avoid un-intentional starting of the cut-off machine.
DO NOT hold the workpiece by hand. Use base vice to secure the workpiece.
DO NOT use the cut-off machine for a task it is not designed to perform.
DO NOT allow untrained persons to operate the cut-off machine.
DO NOT get the machine wet, or use in damp or wet locations or areas where there is condensation.
WARNING! DO NOT use the cut-off machine where there are flammable liquids, solids or gases such as paint solvents and including waste wiping
rags etc.
DO NOT operate the cut-off machine if any parts are missing or damaged as this may cause failure and/or personal injury.
DO NOT remove the safety guard whilst the cut-off machine is in use.
DO NOT attempt to remove a workpiece until the blade has stopped rotating.
DO NOT touch the workpiece close to the cut as it will be very hot. Allow to cool. The cut edge of the workpiece will also be very sharp.
DO NOT leave the cut-off machine operating unattended.
DO NOT operate the cut-off machine when you are tired or under the influence of alcohol, drugs or intoxicating medication.
When not in use switch off the cut-off machine and remove the plug from the power supply.
To move the cut-off machine, lock the machine head with the locking plate and lift by the handle.
2. APPLICATION & SPECIFICATIONS
Ø180mm TCT blade cuts slow and cold without the need for coolant fluid. Will handle steel, wood, brass, aluminium and most plastics, without
the need to change blades. Even hidden nails/screws in timber are no longer a problem. Powered by a 1280W motor. Cast alloy base for added
strength, while retaining portability. Featuring robust saw arm and quick action mitring vice. Fully guarded and fitted with a dead man's trigger
control to prevent accidental starting. Supplied with BS fully approved 13Amp plug.
Size of blade: . . . . . . . . . . . . . . . . Ø180mm
Blade: . . . . . . . . . . . . . . . . . . . . . SM180B36
Max. cutting capacity @ 90°(bar): . . . 45mm
Max. cutting capacity @ 90°(pipe): . Ø50mm
Max. cutting capacity @ 45°(bar): . . . 32mm
Max.Cutting capacity @ 45°(pipe):. . Ø32mm
Motor: . . . . . . . . . . . . . . . . . . 1280W - 230V
3. CONTENTS
Unpack the product and check the contents. Ensure that there is no damage. If any problem is noted, contact your supplier immediately.
Fig.1
© Jack Sealey Limited
No load speed: . . . . . . . . . . . . . . . . 3500rpm
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . 8.1kg
Noise power: . . . . . . . . . . . . . . . . 92.3dB(A)
Noise Pressure: . . . . . . . . . . . . . 105.3dB(A)
Vibration (load): . . . . . . . . . . . . . . 5.793m/s²
Vibration (no load): . . . . . . . . . . . . . . 1.5m/s²
Original Language Version
Fig 1
SM180B
Issue: 4(I) 25/02/14
Advertisement
