1. Manuals
  2. Brands
  3. Solidpump Manuals
  4. Water Pump
  5. TBZ Series
  6. Operation & service manual

Solidpump TBZ Series Operation & Service Manual

S ubme r s i b l e d r a i nage pump
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Solidpump Europe SIA
Uriekstes iela 14a
Rīga, LV -1005
LATVIA
Tel.: + 371 66164228
E-mail: info@solidpump.com
www.solidpump.com
Declaration of Conformity
Tha
the operating instructions before use, and safe keeping.
TBZ / TBZE
S u b m e r s i b l e D r a i n a g e p u m p
OPERATION & SERVICE MANUAL
SOLIDPUMP EUROPE SIA
series

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TBZ Series and is the answer not in the manual?

Questions and answers

Related Manuals for Solidpump TBZ Series

Summary of Contents for Solidpump TBZ Series

  • Page 1 TBZ / TBZE series S u b m e r s i b l e D r a i n a g e p u m p OPERATION & SERVICE MANUAL Solidpump Europe SIA Uriekstes iela 14a Rīga, LV -1005 LATVIA Tel.: + 371 66164228...

  • Page 2: Table Of Contents

    Make the electrical connections G r o u n d i n g from whom you purchased the equipment or the Solidpump C o n n e c t i n g t h e c a b l e s Europe SIA sales office in your area.

  • Page 3: Introduction

    A hazardous situation which, if not avoided, could result in Spare parts CAUTION: minor or moderate injury Solidpump guarantees that spare parts will be available for 10 years after the manufacture of this product has been discontinued. A potential situation which, if not avoided, could NOTICE:...

  • Page 4: Safety

    1. Remove contaminated clothing. C h e m i c a l s o r provided by Solidpump. If there is a question regarding the intended use of hazardous fluids on 2. Wash the skin with soap and water for at least 1 minute.

  • Page 5: Intended Use

    Application limits (page 9). If there is a question regarding the intended use of the equipment, ple ase contact a Solidpump representative before proceeding. WARNING: Only Ex-approved pumps may be used in an explosive or flammable environment.

  • Page 6: Tbze Technical Data And Function

    1.2 times NOTICE: Automatic recovery protection rated current If you discover any damage or discrepancy, please contact with the Solidpump dealer from whom you purchased the product or the Low-voltage nearest Solidpump representative office. 323V Automatic recovery protection (3) Product specification...

  • Page 7: Installation

    4. Installation (1) Preparation for installation Listed below are tools and instruments that are needed to install the submersible pump for DANGER: general dewatering purpose. Disconnect and lock out electrical power before installing or servicing the unit. WARNING: Do not install the starter equipment in an explosive zone unless it is explosion-proof rated.

  • Page 8: Make The Electrical Connections

    CAUTION: Handle the pump carefully. When If an excessive amount of sediment is drawn into the pump, it may cause the pump suspending the pump to raise or to lower it, attach a wire rope or a chain to wear, which can lead to current leakage or electrical shock. to the pump's handle.

  • Page 9: G R O U N D I N

    If the outer sheath of the cable is damaged, then replace the cable. Contact a Solidpump service shop. The voltage drop in long cables must be taken into account. The drive unit's rated voltage is the voltage measured at the cable connection point in the pump.

  • Page 10: Operation 1

    Once again, check the nameplate of the pump to verify that its voltage and Electric circuit frequency are correct. diagrams Check the wiring, power supply voltage, the capacity of the ground leakage circuit breaker, and the insulation resistance of the motor. NOTICE: nsulation resistance reference value 30M .

  • Page 11: M O T O R P R O T E C T I O N S Y S T E

    1. Circle thermal protector dealer where you purchased the equipment or the sales Solidpump The TBZ pump( 11kW) is equipped with an internal motor protective office in your area. device (circle thermal protector).

  • Page 12: W Ater Level During Operation 1

    Touch-up paint must be provided by the user. If the pump must be disassembled due 50TBZ(E)2.2 80TBZ(E)2.2 to damage or loose bolts or nuts, contact the dealer from whom you purchased the equipment or the Solidpump sales office in your area. 50TBZ(E)3.7 80TBZ(E)3.7 (1) Inspection 100TBZ(E)3.7...
  • Page 13 Every 12 months or after 6,000 hours of use, whichever comes first. NOTE: 50TBZ(E)2.2 80TBZ(E)2.2 Yearly Contact the dealer from whom you purchased the equipment or the 50TBZ(E)3.7 80TBZ(E)3.7 1100 Solidpump sales office in your area to inspect and replace the 100TBZ(E)3.7 mechanical seal. 1100 80TBZ(E)5.5 100TBZ(E)5.5 Overhaul 100TBZ7.5 150TBZ7.5...
  • Page 14 The Exchange or maintenance of mechanical seal must be handled by the qualified staff. If omissions, contact sales office in your area. qualified staff. If omissions, contact sales office in your area. you find any Solidpump you find any Solidpump...
  • Page 15 Solidpump correct or contact with the nearest The shaft is bending agency of Solidpump...

This manual is also suitable for:

Tbze series50tbz(e)80tbz(e)100tbz(e)150tbz

Table of Contents