Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Infrico Vitrine
Summary of Contents for Infrico Vitrine
- Page 1 Review: 00 Date: May 31, 2018 Page: 1 to 13...
-
Page 2: Table Of Contents
INDEX 1. Introduction ……………………………………………….…………….. 3 2. Warning ……………………………………………….…………………… 3 3. Description…..…………………………………………….……………… 4 4. Transport and mobility………………………………….…………… 4 5. Conditions of use and Technical specifications…….…..4 5.1 Command and control.………..……………………….…..5 5.2 Protection and safety device………………………….…….. 5 6. Installation……………………………………………………………..6 6.1 Preliminary operations….……………………..……….……. 6 6.2 Positioning…….………………………….………..……………... -
Page 3: Introduction
1. INTRODUCTION This manual has been made in a simple way so that by reading it you can know the operation and maintenance of our furniture. It is recommended to read it carefully and keep it for any query. The manufacturer is not liable for damages to persons or objects that may be caused by non- compliance with the prescriptions contained in this manual. -
Page 4: Description
3. DESCRIPTION There apparatus of cold and hot elements is composed of a tank or plate inserted ina a cabinet with support, and a heating or cooling group housed in the bottom of the tank. The control panel is located in the lower rear part where you can control the temperature. The element Bath Maria and cold elements is available with the unified dimensions GN 2 1/1, GN 3 1/1, GN 4 1/1, GN 5 1/1 (Drop-in) and 6 1/1 (Self), to be installed in collective facilities varying the configuration. -
Page 5: Command And Control
MODELS TEMPERATUR RANGE Vitrine +4ºC/+12ºC Cold Plate -4ºC/+4ºC Cold Tank 0ºC/+6ºC Reserve +2ºC/+10ºC 5.1 Command and control The control device is grouped on a board described in Figure 1 for the Bain Marie, the Figure 2 for Glass Ceramic and the figure 3 for the cold elements. Electrical components meet the safety standards. -
Page 6: Installation
In the case of Glass Ceramic incorporate a safety thermostat incorporated in a board with automatic reset. Device of individual protection: The use of gloves is advised because of the high temperature on food containers. Special provisions to comply risk of waste: Limit access to any person, which have to be informed of the potential hazard due to high temperature. -
Page 7: Water Connection
6.3 Water connection (fixed mount) Under the lower plane is visible the pipeline loading and unloading. Splice the tube of load with the pipeline using a flexible pipe. Splice the unloading of the tank to siphon of the pipeline of drain installed in the premises (See annex Nº1). -
Page 8: Start-Up Bain-Marie
use for any other function. In the cold elements the lower part serves for the storage or maintenance of food in the case of refrigerated storage. • The dimensions of the tank allow different lengths 2, 3, 4, 5, 6 modules GN 1/1 respectively. •... -
Page 9: Start-Up Of Cold Elements
thermostat is turned. Continuing the rotation is set to the desired temperature. The graduated scale is only indicative. • In the case of the model is also provided hot store proceed in the same way as in the Bain Marie for the start of this. -
Page 10: Cleaning And Maintenance
b) Empty and carefully clean the tank. c) Protect the INOX surface with a layer of vaseline oil vigorously wiping oil-soaked. d) Periodically ventilate the room, leaving the closet door open, to avoid unpleasant odors. 8. MAINTENANCE AND CLEANING 8.1 Cleaning Procedure Cleaning the cabinet To clean the cabinet, the following instruction should be followed: •... -
Page 11: Trouble Shooting Chart
WARNING: Make sure that the equipment is unplugged before cleaning or repairing it. In case of failure, if the problem persists after you have carried out the indicated checks, “DO NOT MAKE ANY REPAIRS YOURSELF”. Contact our Technical Service. Always provide the cabinet model and serial number (located on the data plate, 13 digits). - Page 12 PROBLEM POSSIBLE SOLUTION 1.- Low voltage. 2.- Unit wired incorrectly. Compressor will not start-no 3.- Starting capacitor defective. hums but cycles on overload. 4.- Starting capacitor seal. 5.- Compressor motor defective. 6.- High head pressure. 1.- Insufficient refrigerant charge. Head pressure to low 2.- Leak in the system.
-
Page 13: Recycled
9. RECYCLING At the end of the useful life of the equipment, you must be disconnected from the mains for dismounting of its components. The equipment has to be dismantled, respecting existing laws, particularly in regard to the recovery of refrigerant gas. The different components (electrical parts, rubber tubes, grommet, etc…) have been selected to obtain the best results, while respecting the environment.
Need help?
Do you have a question about the Vitrine and is the answer not in the manual?
Questions and answers