Subscribe to Our Youtube Channel
Summary of Contents for Sub-Zero Wolf Outdoor Pro Wall Hood
-
Page 1: Table Of Contents
subzero.com 800.222.7820 Outdoor Pro Wall Hood Service Manual General Information Component Access & Removal Troubleshooting Guide Technical Data Wiring Diagrams... -
Page 2: General Information
Pro Outdoor Hoods General Information service.subzero.com GENERAL INFORMATION SERVICE MANUAL INTRODUCTION This service manual helps with troubleshooting and diagnosing malfunctions, completion of repairs, and return of the product to proper operating condition. Read the complete instructions contained within before initiating any repairs. This guide is intended for use by Factory Certified Service. - Page 3 Pro Outdoor Hoods General Information service.subzero.com UNIT WARRANTY Product warranty is determined by the installation location and the date of installation. http://service.subzero.com/ ▪ View product warranties at ClaimsAndOrderProcessing/Pages/WarrantyInfo Warranties start on the day of product installation. ▪ Search for warranty and service information by serial ▪...
-
Page 4: Component Access & Removal
Pro Outdoor Hoods Component Removal and Installation service.subzero.com COMPONENT REMOVAL AND INSTALLATION Remove the halogen lamp from the unit. FILTER ASSEMBLY REMOVAL Remove the Filter Assembly Hold the filter assembly by the knobs, and push the filter assembly toward the top of the hood. Pull the bottom of the filter assembly toward the center of the hood. - Page 5 Pro Outdoor Hoods Component Removal and Installation service.subzero.com REMOVE THE LAMP SOCKET (continued) Remove the lamp socket from the unit. BLOWER KNOB INSTALLATION Install the Blower Knob Place the blower knob onto the blower switch shaft. Use a " Allen wrench to tighten the set screw in the blower knob.
- Page 6 Pro Outdoor Hoods Component Removal and Installation service.subzero.com Remove the wire cover from the unit. GREASE CUP REMOVAL To remove the grease cup, first remove: Filter assembly Remove the Grease Cup Lift the grease cup from the lower channel of the hood. Remove the grease cup from the unit.
- Page 7 Pro Outdoor Hoods Component Removal and Installation service.subzero.com REMOVE THE BLOWER MOUNTING PLATE (continued) Remove the blower mounting plate from the unit. Remove the internal frame from the unit. BLOWER MOUNTING PLATE INSTALLATION INTERNAL FRAME INSTALLATION After installing the blower mounting plate, install: After installing the internal frame, install: Filter assembly Grease cup...
- Page 8 Pro Outdoor Hoods Component Removal and Installation service.subzero.com REMOVE THE INNER PANEL (continued) Lower the inner panel, and disconnect the blower and light Use a Phillips screwdriver to install the screws into the inner switch wire connectors. panel. Disconnect the wire connector from the blower speed control.
- Page 9 Pro Outdoor Hoods Component Removal and Installation service.subzero.com BLOWER PLUG SOCKET REMOVAL BLOWER SWITCH REMOVAL WARNING WARNING Turn off the power to the product before starting this Turn off the power to the product before starting this procedure. procedure. To remove the blower plug socket, first remove: To remove the blower switch, first remove: Filter assembly Filter assembly...
- Page 10 Pro Outdoor Hoods Component Removal and Installation service.subzero.com INSTALL THE BLOWER SWITCH (continued) Connect the wire from the blower speed control to the blower switch. Install the Light Switch Insert the light switch into the hood. LIGHT SWITCH REMOVAL BLOWER SPEED CONTROL REMOVAL WARNING Turn off the power to the product before starting this WARNING...
- Page 11 Pro Outdoor Hoods Component Removal and Installation service.subzero.com INSTALL THE BLOWER SPEED CONTROL (continued) Use a " socket to install the nut onto the blower speed control shaft. Connect the wire connector from the blower switch to the blower speed control. 10"...
-
Page 12: Troubleshooting Guide
Pro Outdoor Hoods Troubleshooting Guide Pro Wall Hood service.subzero.com TROUBLESHOOTING GUIDE PRO WALL HOOD This section explains how to troubleshoot various components in a Wolf Pro Wall Hood. WARNING To avoid electric shock, disconnect power to the hood when preparing for tests. Care should be used while doing any test with the hood energized. - Page 13 Pro Outdoor Hoods service.subzero.com PRO WALL HOOD TROUBLESHOOTING TABLE Symptom Possible Cause or Diagnostic Test Resolution Hood lights and blower do The breaker is open. Reset the breaker. not turn on. GFCI circuit is tripped. The unit should not be installed on a GFCI circuit. Change the outlet type.
- Page 14 Pro Outdoor Hoods Test Procedures service.subzero.com TEST PROCEDURES Measure the resistance from the plug Neutral to the blower casing. TEST THE LINE VOLTAGE IN THE WIRING BOX If the reading is open from L1 to Neutral or there is continuity from L1 or Neutral to the blower case, replace the WARNING blower.
-
Page 15: Technical Data
Pro Outdoor Hoods Technical Data service.subzero.com TECHNICAL DATA PRO WALL HOOD TECHNICAL DATA PRO WALL HOOD TECHNICAL DATA Parameter Value AC power 110 VAC to 127 VAC Blower switch 828568 125 VAC 20 A Light switch 828569 125 VAC 20 A Blower speed control 828570 120 VAC 7 A (Max) Heat sensor 828571... -
Page 16: Wiring Diagrams
Pro Outdoor Hoods Wiring Diagrams service.subzero.com WIRING DIAGRAMS OUTDOOR PRO WALL HOOD WIRING DIAGRAM 828743 REVA 02/2019... - Page 17 Pro Outdoor Hoods Wiring Diagrams service.subzero.com 828743 REVA 02/2019...
Need help?
Do you have a question about the Wolf Outdoor Pro Wall Hood and is the answer not in the manual?
Questions and answers