Related Manuals for Valen RE856
Summary of Contents for Valen RE856
- Page 1 OPERATION MANUAL RE856 BATTERY TESTER AUSTRALIA NEW ZEALAND 1300 734 253 0800 734 253 sales@valen.com.au sales@valen.co.nz www.valen.com.au www.valen.co.nz...
- Page 2 Regal Electro, a battery and security component its core product range, Power Charge. The Power supplier based in Lake Cargelligo, NSW. Charge range was renamed Valen, which in Latin means ‘Power’. Brisbane operations also began at Over the next few years, it became this time.
- Page 3 A company built on its Core Values. Wow Customers through Service - Our customers want service and we want our employees to go above and beyond for our customers. - We expect our employees to deliver a WOW experience with customers. Move Fast &...
-
Page 4: Table Of Contents
Dual display to show the internal resistance and voltage of the battery simultaneously. – The RE856 has 99 sets of composite comparator function, which can be set at resistance and voltage values to get the reliable detection of battery deterioration. -
Page 5: Names & Functions Of Parts
RE856 OPERATION MANUAL NAMES & FUNCTIONS OF PARTS AUS 1300 734 253 NZ 0800 734 253... -
Page 6: Switches & Input Terminals
RE856 OPERATION MANUAL Switches & Input Terminals LCD Display key: To turn the beeper on or off – To decrease the displayed value – Hold this key for 2 seconds to change the temperature units – key: To store one set of readings to memory –... -
Page 7: Screen Display
RE856 OPERATION MANUAL Screen Display Auto power off function is enabled Measured battery total capacity Resistance zero-adjustment function is on The calculated remaining capacity of the battery Display is locked Shown when the comparator function is on Auto-hold function is on... -
Page 8: Specifications
Accessories Clip-type test lead with temperature sensor, pin-type test lead, DCA current adaptor, zero- adjustment board, operation manual, batteries, AC adaptor, USB cable, CD PC software (also available at www.valen.com.au), carrying case. AUS 1300 734 253 NZ 0800 734 253... -
Page 9: Electrical Specifications
RE856 OPERATION MANUAL Electrical Specifications Conditions to Guarantee Accuracy Temperature 23°C ± 5°C Humidity 80% RH or less (no condensation) Temperature coefficient 0.10 x (specified accuracy)/°C (<18°C to >28°C) Zero-adjustment After zero adjustments for each range Resistance measurement Range Resolution... -
Page 10: Operation
RE856 OPERATION MANUAL OPERATION Preparation The following safety information must be observed to ensure maximum personal safety during the operation of this tester. To avoid electric shock when replacing the batteries, first disconnect the leads from the object to be measured. -
Page 11: Operation
RE856 OPERATION MANUAL Operation Read the battery internal resistane, DC voltage and temperature directly from the display. When using the clip type test lead, the temperature sensor is detected, and the temperature is automatically displayed. Press the key for 2 seconds to change the displayed temperature unit. -
Page 12: Pin-Type Test Lead Zero-Adjustment
RE856 OPERATION MANUAL Pin-type Test Lead Zero-Adjustment When the resistance reading is lower than 200 digits and stable, the zero-adjustment is automatically carried out. The would then stop flashing, and the beeper sound would also stop. Remove the pin-type test leads from the zero-adjust board and start the measurement, connect the leads to the battery to test. -
Page 13: Moving Average Function
RE856 OPERATION MANUAL Moving Average Function If the resistance measurement value is unstable, this can be corrected with the moving average function. Press and hold down the key, then rotate the resistance range switch to any range to turn on the meter, to samples select mode, ‘SET’... -
Page 14: Disable Auto Power-Off Function
RE856 OPERATION MANUAL Disable Auto Power-off Function If no switch operation for 10 minutes, the meter automatically powers off. Auto data memory and continuous data logging mode will auto-disable the auto power-off function. For continuous measurement, in some cases it may be necessary to disable the auto power-off function. -
Page 15: Comparator Table
RE856 OPERATION MANUAL Comparator Table Resistance Low Limit Resistance High Limit Resistance Voltage Middle High Voltage Comparison Beeper Beeper Beeper Value High Beeper Beeper Voltage comparison value = (high limit voltage value + low voltage value)/2. Start/Stop Controls for the Comparator... -
Page 16: Data Memory Function
RE856 OPERATION MANUAL Power on the battery charger, the meter will display the charge current value with a plus sign and the battery accumulated charging capacity ( Connect the battery load to the battery and use the DC current adaptor. Clamp the current transducer (jaw) around the ‘+’... - Page 17 RE856 OPERATION MANUAL To Auto Memorise the Reading Press the key for 4 seconds; the display will show SWT INTV. Using the keys, select the desired interval time from 3 seconds to 255 seconds. Press the key to exit. Press the key for 2 seconds to auto memory mode;...
-
Page 18: Maintenance Cleaning
Repairs or servicing are not covered in this operation manual and should only be performed by qualified personnel. Please return the meter to VALEN if this is the case. Periodically wipe the case with a dry cloth. Do not use abrasives or solvents on this instrument. -
Page 19: Online Operation
RE856 OPERATION MANUAL If a ‘User Account Control’ windows opens asking ‘Do you want to allow the following program from an unknown publisher to make changes to this computer?’ click ‘Yes’ Online Operation Run the Software Click ‘Run BatCapTesterS.exe icon on the dektop. -
Page 20: Download Data
RE856 OPERATION MANUAL Click the button in the top left corner of the main screen. A dialogue box will open - input a file name then click to begin saving data to the file just created. Click the button to stop recording. -
Page 21: Data Convert
RE856 OPERATION MANUAL Data Convert Excel Open Microsoft Excel and locate the saved file in Excel format, for example, test.xls. The ‘Text Import Wizard’ then appears. Follow the steps from 1 to 3 to complete. Graph Open a saved data file in the software program and click the button forth from the left. -
Page 22: Sampling Time
RE856 OPERATION MANUAL Sampling Time PC Sampling Time PC sampling rate is the rate at which the PC collects readings while connected to the meter. Click the button fifth from the left on the main menu. Meter Sampling Rate Meter sampling rate is the rate at which the meter stores readings. Click the button fifth from the left on the main menu. -
Page 23: Set Comparator
RE856 OPERATION MANUAL Set Comparator Click the button fifth from the right on the main menu. Click to set the meter. Erase EEPROM To erase the EEPROM, click the button second from the right on the main menu. Click to confirm.