Related Manuals for Sutron INTEGRA-TR
Summary of Contents for Sutron INTEGRA-TR
- Page 1 INTEGRA-TR INTEGRATED WIRELESS MODEM VHF 132-174 MHZ UHF 380-512 MHZ 900 MAS 928-960 MHZ SUTRON PART NUMBER 6661-1249-1 APPLICATION NOTE PREPARED BY: INTEGRATED SYSTEMS DIVISION 2009...
-
Page 2: Table Of Contents
APPLICATION NOTE Integra-T R Integrated Modem TABLE OF CONTENTS 1..........INTRODUCTION 2......PROGRAMMING THE RADIO 3...... SERIAL PORT CONNECTIONS 3.1 I 9210.........9 NTEGRA WITH 3.2 I 8210 ........9 NTEGRA WITH 4.......RADIO SETTINGS & TESTING 4.1 X ..............10 LITE 4.2 X ............13 CONNECT 5........ -
Page 3: Introduction
Integra-T R Integrated Modem 1. Introduction The Dataradio Integra-TR integrated wireless modem provides advanced features without complicated system setup. Designed specifically for data transmission, this programmable, transparent modem transmits data real-time without delays at speeds up to 19.2 kbps. With enhanced diagnostics it is the perfect choice even in the harshest environments. -
Page 4: Programming The Radio
APPLICATION NOTE Integra-T R Integrated Modem 2. Programming the Radio Download the programming software from the following link. http://www.dataradio.com/4_2.html Proceed with the following steps to program the radio. Connect the power connector on the back of the radio. Also, connect the 5W load resistor and rubber duck antenna to the RF port of the radio. - Page 5 APPLICATION NOTE Integra-T R Integrated Modem Figure 1. IntegraTR Programmer main window e. Click on the Read toolbar button on the screen. This step will update the program with the latest settings in the radio. From the main menu, select Utilities|Port Settings (Figure 2. Port Settings window).
- Page 6 APPLICATION NOTE Integra-T R Integrated Modem Figure 2. Port Settings window g. Make sure your settings match the settings above in Figure 2; if not, make any necessary changes. Click OK when finished. Never change the Baud Rate in the Port Settings window. This baud rate is just for your PC to talk to the radio.
- Page 7 APPLICATION NOTE Integra-T R Integrated Modem h. Click on the Parms toolbar button in the main window. Figure 3. Modem parameters setup window will appear. Make sure the Modem tab is selected. Select the Network Speed. For 8210/9210s select 9600 Half Chan if you have one frequency for TX and RX. If you have separate TX and RX frequencies, select [XXXX].
- Page 8 APPLICATION NOTE Integra-T R Integrated Modem Next, click on the Com/Analog tab in the Modem/Radio Parameters window (Figure 4). Select the desired radio communications baud rate. For details on these settings, please see the INTEGRA technical manual section 2.4.4.3. Figure 4. Com/analog parameters setup window...
- Page 9 APPLICATION NOTE Integra-T R Integrated Modem Lastly, click on the Radio Tab to program the frequency (Figure 4). Enter the RX/TX frequencies and the power. A power value of 255 is equivalent to 5 W power. Click OK to save all parameter settings. For details on these settings, please see the INTEGRA technical manual section 2.4.4.4 Figure 5.
- Page 10 APPLICATION NOTE Integra-T R Integrated Modem Figure 6. Write in progress window After the programming is done the window will go blank and Figure 7 will appear. Disconnect the programming cable from you radio. The radio is now programmed. Figure 7. Program complete window...
-
Page 11: Serial Port Connections
3.1 Integra with 9210 9210 COM2 – Radio cable: Sutron Part # 6411-1484. Radio – PC cable: Sutron Part # 6411-1484. Antenna Jumper cable (Antenna – Polyphaser): Sutron Part # 6411-1522-12 (SMA Male to N- Male). Polyphaser: Sutron Part # 1311-1056 or 1311-1057. -
Page 12: Radio Settings & Testing
4. Radio Settings & Testing 4.1 Xlite Please read Sutron Xpert/Xlite Manual on how to connect to Xpert/Xlite with the Xterm program. After Connecting to the 9210 with the Xterm go to the following window under the Setup Tab . - Page 13 APPLICATION NOTE Integra-T R Integrated Modem The following window will appear. In this window select Radio2 under Port and press the Send Mail button. Pressing Send Mail will cause the system to prompt for a destination and a message. The destination should be a master station ( Xconnect Master ID which is XCONNECT by default) After typing the destination unit id click OK.
- Page 14 APPLICATION NOTE Integra-T R Integrated Modem Type the message in following window. You can leave it on the default Testing 1 2 3 message also. Whatever message you type in the following window it will appear in the Xconnect SSP Decoder window running at the base station PC.
-
Page 15: Xconnect
APPLICATION NOTE Integra-T R Integrated Modem 4.2 XConnect Configure a Station in the Xconnect based on the unit id and other information in the Remote Xpert/Xlite . Set the Com port of Xconnect to the Type Radio, baud rate 9600 as follows... - Page 16 APPLICATION NOTE Integra-T R Integrated Modem Start the Xconnect Program and click on the XC RTU window and also click on the SSP Decoder.
- Page 17 APPLICATION NOTE Integra-T R Integrated Modem Click on the Green button (Under the Polling & Options) and following window will appear. Select the Station and click on the Poll Type as Current. Click on the Poll Now button and you should get an almost instant response back from the Remote Xpert/Xlite as shown in the above window.
-
Page 18: Interface Definition
APPLICATION NOTE Integra-T R Integrated Modem 5. Interface Definition 5.1 Integra-TR Data Interface Communication and Setup connectors: DE-9F Power/Analog connector: Snap and lock 4-pin Description Description 1 DCD Data Carrier Detect 1 +13.3 VDC (red) 2 RXD RX Data 2 Ground (black) -
Page 19: Integra Tr Technical Specifications
APPLICATION NOTE Integra-T R Integrated Modem 6. Integra TR Technical Specifications Modem 6.25 KHz* 12.5 KHz 25 KHz Channel Bandwidth Data Rate (user selectable) 2400, 4800 bps 4800, 9600 bps 4800, 9600, 19200 bps DRCMSK Modulation RTS/CTS Delay 4 msec @ .35 μV (2400 bps) @ 1.4 μV @ 1.0 μV (9600 bps);... - Page 20 APPLICATION NOTE Integra-T R Integrated Modem ETSI 300.113 (403-470 Mhz) 300.113 < 2.0 A < 1.8 A < 2.5 A Current Drain (Tx @ 13.3 VDC) Current Drain (Rx @ 13.3 VDC) < 220 mA (with a terminal connected to the COM port) 15 mA nominal Current Drain (Power Save Mode) Frequency Tolerance...
Need help?
Do you have a question about the INTEGRA-TR and is the answer not in the manual?
Questions and answers