Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for AS M0026
Summary of Contents for AS M0026
- Page 1 2020.06.22 M0026 USER MANUAL TESTER FOR DIODES & RECTIFIERS...
-
Page 3: Table Of Contents
English User Manual - M0026 Tester CONTENTS ........................INTRODUCTION ........................... 1. PURPOSE ..................2. TECHNICAL CHARACTERISTICS ...................... 3. EQUIPMENT PACKAGE ..................4. DESCRIPTION OF THE DEVICE ......................... OPERATION ......................5.1 Safety regulations ....................... 5.2 Rectifier testing ........................5.3 Tester setup .................... -
Page 4: Introduction
M0026 has been engineered to satisfy the demand of big service stations and alternator repair shops for the device which would allow quick and accurate rectifier health checks. Testing rectifiers with the use of multimeter has always been the most common practice.This method has a significant... -
Page 5: Technical Characteristics
English User Manual - M0026 Tester 2. TECHNICAL CHARACTERISTICS 219×214×80 Dimensions (L*W*H), mm Weight, kg Supply voltage, V Supply frequency, Hz Single-phase Supply type No more than 40 Consuming power, W Current load of diode test, A The voltage on the open contact probes of the device, V 3. -
Page 6: Equipment Package
-cable with a probe – 1 pc., -cable with a clamp – 1 pc., -User Manual – 1 pc. Inspect M0026 tester. If any damage is detected, please contact the manufacturer or sales representative before launching the equipment. WARNING! In case of obvious damage, the operation of the device is forbidden. -
Page 7: Operation
English User Manual - M0026 Tester Fig.2. Diagnostic cables Fig.3. M0026 tester. Back view: 1 – Diode fuse; 2 – Power connector. 5. OPERATION OF THE DEVICE 1.Use the device as intended. 2.The tester is intended for indoor use. When used outdoors, external conditions and technical characteristics of the device set out in item 2 of this manual, should be taken into consideration. -
Page 8: Safety Regulations
In case of obvious damage, replace them with the new ones before launching the device. 5.2. Rectifier testing Diagnostics of a rectifier should be performed as follows: 1.Turn the tester on. Connect the clamp to the rectifier housing. The following message will appear on the screen: “CONNECT PROBE TO DIODE”. - Page 9 English User Manual - M0026 Tester 2.1. If the diode is faultless, the screen will display “Vf” and “Vr” values. The screen color will be green. 2.2. If the "Vf” value is higher than normal, the screen color will be yellow.
-
Page 10: Tester Setup
English User Manual - M0026 Tester 5.3. Tester setup The device assesses the diode performance on the basis of the forward voltage drop value (“Vf”) and is specially calibrated to make it usable for any operator who doesn’t have sufficient knowledge of the diode parameters and characteristics. -
Page 11: Cleaning And Care
•Whether the measuring probes are in healthy condition (visual inspection). •Do not store or use the device in premises where there is a high temperature, humidity, danger of explosion or fire, strong magnetic field. As a result of exposure to dampness, the tester performance may deteriorate. -
Page 12: Equipment Disposal
European WEEE Directive 2002/96/EC (Waste Electrical and Electronic Equipment Directive) applies to M0026 disposal. Obsolete electronic equipment and electric appliances including cables and hardware as well as batteries and accumulators must be disposed of separately from the household rubbish. Use available waste collection systems to dispose of outdated equipment. - Page 14 Produced by 18 Biolohichna St. 61030 Kharkiv, Ukraine +38 (057) 728 0171 Technical Support: support@servicems.eu General Enquiries: sales@servicems.eu Skype: MSG Equipment servicems.eu...
Need help?
Do you have a question about the M0026 and is the answer not in the manual?
Questions and answers