Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for MOBA ROTEC LS.RH.HP
- Page 1 USER MANUAL ROTEC LASER LEVEL LS.RH.HP LS.RHV LS.RHVG...
- Page 2 All other equipment: 1 year MOBA Australia or its authorised service centre will repair or replace, at its option, any defective part or component of which notice has been given during the warranty period. A warranty registration card must be filled out properly and be on file with the MOBA Australia service department before warranty repair or replacement can be approved.
-
Page 3: Table Of Contents
4.3.2 Levelling 90 Willandra Drive, Epping, 3076, Victoria, Australia 4.3.3 Rotating head speed moba-automation.com.au 4.3.4 Scanning function MCE Lasers ® is a registered trademark of MOBA Mobile 4.3.5 Slope adjustment Automation Australia Pty Ltd 5. Charging the laser 6. Remote All rights reserved. -
Page 4: Maintenance And Safety
The laser should be transported or carried carefully to avoid impact or vibration. • The laser should be stored in the carry case and packed with cushioning material. Always handle the • laser with care. Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 5: Principles Of Operation
The laser automatically emits following beam(s): The laser automatically emits following beams: horizontal scanning surface (all models) Vertical scanning surface • • plumb dot (all models except LS.RH.HP) Horizontal dot • • Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 6: Physical Features
3. PHYSICAL FEATURES 3.1 MAIN BODY LIGHTHOUSE ROTATING HEAD HANDLE SWITCHPAD BATTERY PACK Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 7: Switchpad
1. ON/OFF switch 6. HI alert indicator 4. Mode indicator 5. HI alert 3. Automatic/manual mode 9. Beam left 7. Scanning angle 10. Beam right 8. Rotating head speed 11. X-axis 12. Y-axis Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 8: Switchpad Functions
10. Beam right: moves the laser beam clockwise, only when the unit is in 0 RPM or scan mode 11. X-axis: adjusts the slope of the X-axis when the instrument is in manual mode. 12. Y-axis: adjusts the slope of the Y-axis, when the instrument is in manual mode. Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 9: Using The Rotec Laser
4.3 OPERATION 4.3.1 POWER Press the ON/OFF switch to switch the laser on. If the power indicator flashes, the voltage of the batteries is low and batteries need to be replaced or recharged. Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 10: Levelling
Continue to press the Rotating Head Speed switch and set the speed to 0 RPM. The rotating head will stop rotating. To move the laser rotating head clockwise, press the Beam Right switch. To move the laser rotating head counter-clockwise, press the Beam Left switch. Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 11: Scanning Function
Press the Y-axis up or down switch to move the laser beam up or down. To return to automatic mode, press the Automatic/Manual Mode switch. Automatic mode is indicated by the Mode Indicator light switching off. Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 12: Charging The Laser
The instrument can be used while charging. • If the laser will be kept in storage or left unused for a long time, the batteries (alkaline or rechargeable • battery) should be taken out. Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 13: Remote
NOTE: the remote is an optional accessory for LS.RH.HP model. Functions that can be controlled by the remote are as follows: Rotating head: see section 4.3.3 • Directional scanning: see section 4.3.4 • Slope adjustment: see section 4.3.5 • Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 14: Accuracy Checking
5 mm. If the distance between H1 and H2 in either axis is more than 5 mm, the laser should be sent to your authorized dealer for service / calibration 50 Meters Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 15: Horizontal Line Checking
7. The distance between hA and hA’ should be less than 3 mm. If the distance is more than 3 mm, the laser should be sent to your authorized dealer for service. Wall A Wall A Wall B Wall B Copyright © MOBA Mobile Automation Australia Pty Ltd... -
Page 16: Specifications
IP 55 Dimensions (L x W x H) 160 x 160 x 185 mm 160 x 160 x 185 mm 160 x 160 x 185 mm Weight 2.0 kg 2.0 kg 2.0 kg Copyright © MOBA Mobile Automation Australia Pty Ltd...
Need help?
Do you have a question about the ROTEC LS.RH.HP and is the answer not in the manual?
Questions and answers