Download Print this page
Altinex TE460-137 User Manual

Altinex TE460-137 User Manual

2k/4k hdmi signal generator & analyzer
Hide thumbs Also See for TE460-137:

Advertisement

Quick Links

TE460-137
Welcome!
Everyone at Altinex greatly appreciates your purchase of the
TE460-137. We are confident that you will find it to be reliable and
easy to use. If you need support, please do not hesitate to call us
at 714-990-2300.
At Altinex, we are committed to developing unique and state of
the art Signal Management Solutions
installations. Welcome to the Altinex family of satisfied customers
around the world!
1. Precautions and Safety Warnings
These instructions are to ensure the reliable operation of
your TE460-137 and to prevent fire and shock hazards.
Please read them carefully and heed all warnings.
1.1 General
Qualified Altinex service personnel or their authorized
representatives must perform all service.
1.2 Installation Precautions
To prevent fire or shock, do not expose this unit to water
or moisture. Do not place in direct sunlight, near heaters
or heat-radiating appliances, or near liquid. Exposure to
direct sunlight, smoke, or steam can harm internal
components.
Handle carefully; dropping or jarring can cause damage.
2. Installation Procedures
Note:
Download and read the entire online manual to become familiar with the TE460-137 and for detailed information.
See the top label of the TE460-137 for control details or refer to the complete online manual.
Note 2: Go to
www.youtube.com
Step 1: Insert a small paperclip into the battery compartment slot and press firmly.
Step 2: Install the battery provided with the tester. Make sure the mylar tab is underneath the
battery as shown in the image to the right.
Caution: Make sure the polarity of the battery matches the tester.
Step 3. The tester is now ready; turn on power. The TE460-137 powers up in EASY MODE.
EASY MODE provides the basic functionality required by most users.
If more detailed information or features are required, select ADVANCED MODE as
follows. Press and hold the TASK button for about 2 seconds and wait for the
TE460-137 to reinitialize.
Step 4. Select the desired mode of operation using the TASK button on the front of the tester. Do NOT press ENTER to confirm the
selection. Once the correct task is displayed at the top, just wait for the task to start automatically.
Step 5. Use the MENU and UP/DN arrows to navigate the menus.
ENTER button selects a menu. UP/DN buttons cycle through options. ENTER button confirms the selection.
3. Warranty and Return Policies
Please visit the Altinex website at
please complete a RMA (return material authorization) form located on the bottom left hand corner of the Altinex homepage. Once
completed, please email the form to support@altinex.com.
400-0753-003
2K/4K HDMI SIGNAL GENERATOR & ANALYZER User's Guide
®
for demanding audiovisual
and search TE460-137 for how to videos. Start with EASY MODE.
www.altinex.com
for details on warranty and return policies. In the case of a unit needing repair,
1.3 Cleaning
Clean with a dry cloth only. Never use strong detergents
or solvents such as alcohol or thinner.
1.4 FCC Notice
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 2
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions found herein, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at their own expense.
Any changes or modifications to the unit not expressly
approved by Altinex, Inc. could void the user's authority to
operate the equipment.
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the TE460-137 and is the answer not in the manual?

Questions and answers

Summary of Contents for Altinex TE460-137

  • Page 1 In the case of a unit needing repair, please complete a RMA (return material authorization) form located on the bottom left hand corner of the Altinex homepage. Once completed, please email the form to support@altinex.com.
  • Page 2 Digital Signal types Humidity 60% RH non-condensing HDMI 1.4,3D MTBF (calc.) 38,000 hrs. Signal resolution Up to 4k x 2k Table 2. TE460-137 Mechanical Accessories Included Electrical TE460-137 Power supply 2.4A USB Wall charger (1) Video Input Signals 2.0 USB cable...
  • Page 3 Supports optional Windows control software in EASY or ADVANCED modes The latest firmware supports an EASY MODE option for the TE460-137. In EASY MODE, users have quick access to the most commonly used features. All information is available on a single screen with no need to navigate submenus for information.
  • Page 4 TE460-137 User’s Guide Description 400-0753-003...
  • Page 5 TE460-137 User’s Guide 6. Application Diagrams 400-0753-003...
  • Page 6: Easy Mode

    See section 7.1 Modes of Operation menu items. The TE460-137 powers up in EASY MODE as this is best for 7.1.5 Pattern Mode most users. However, there are many more advanced features and information available using the ADVANCED MODE.
  • Page 7 TE460-137 User’s Guide 7.2 Notes and Limitations 7.3.5 Task Mode Button Press to switch the unit between Analyzer Mode, Pattern 7.2.1 Analyzer Mode, and Cable Test Mode. The CEC line is not affected by the generator. CEC signals pass through the unit, but there is no analysis of the data.
  • Page 8 User’s Guide 7.5 Battery Compartment 7.6 Display Indicators The TE460-137 may be powered directly via the USB port or by a rechargeable Lithium-ion battery (included but packaged 7.6.1 USB Port separately) which is concealed within the bottom of the unit.
  • Page 9 TE460-137 User’s Guide 7.7 OSD Menus 7.7.1 OSD Menu – Analyzer (Menu Listings) Input Setup Hotplug Time 50ms ~ 500ms (150ms) Hotplug Toggle RxSense* DDC Bus* HDCP Port* v1.4 v1.4+v2.2 HDCP REAUTH-REQ 4K to 1080p On YCbCr Out On RGB Out...
  • Page 10 TE460-137 User’s Guide Monitor HDCP (v2.2) Source HDCP [Measured] Rx HDCP Port [Measured] TxCaps [Measured] RxCaps [Measured] Receiver ID [Measured] [Measured] [Measured] Monitor SCDC Rx SCDC Port [Measured] Sink Version [Measured] Source Version [Measured] Scramble Enabled [Measured] Scramble Status [Measured]...
  • Page 11 TE460-137 User’s Guide Audio Timing ACR, AIF, ASP, HBR [Measured] [Measured] [Measured] ASP PLL Lock [Measured] ASP audio FIFO [Measured] ASP Layout [Measured] ASP Ch No. [Measured] CHS App. Type [Measured] CHS Audio Coding [Measured] CHS Ch No. [Measured] CHS Source No.
  • Page 12 TE460-137 User’s Guide EDID Emulator Copy Sink [D1] DVI [Default EDID Details] [D2] VGA [Default EDID Details] [D3] 8B LPCM PC [Default EDID Details] [D4] 8B LPCM HD [Default EDID Details] [D5] 12 BS 720p [Default EDID Details] [D6] 12 BS HD 3D...
  • Page 13 TE460-137 User’s Guide Setup USB Port Power RS-232 OLED Contrast 0 ~ 8 (6) Firmware Update Power Saving 2min ~ 10min EDID Reset Factory Restore Information [Unit Version Details] 400-0753-003...
  • Page 14 TE460-137 User’s Guide 7.7.2 OSD Menu – Pattern Generator (Menu Listings) Output Setup Timing [T1] 720×480p59 [T2] 720×576p50 [T3] 1280×720p25 [T4] 1280×720p30 [T5] 1280×720p50 [T6] 1280×720p60 [T7] 1920×1080i50 [T8] 1920×1080i60 [T9] 1920×1080p24 [T10] 1920×1080p25 [T11] 1920×1080p30 [T12] 1920×1080p50 [T13] 1920×1080p60 [T14] 3840×2160p24...
  • Page 15 TE460-137 User’s Guide Output Setup (cont.) HDMI Format Colorspace YUV444 Full ColorRange Limited Audio LPCM* 5.1CH 7.1CH v1.4 HDCP Out v2.2 HDCP V2.2 AKE_Stored_km() AVMute* Output* Follow +5V Out 400-0753-003...
  • Page 16 TE460-137 User’s Guide Monitor Sink HDCP Port/Auth [Measured] EDID [Measured] SCDC Port [Measured] Monitor HDCP (Output HDCP 1.4) Tx HDCP [Measured] Sink HDCP Port [Measured] Aksv [Measured] Bksv [Measured] Ri Tx [Measured] Ri’ Sink [Measured] Count [Measured] Day 0 00:00:00...
  • Page 17 TE460-137 User’s Guide Audio Output Volume 0 ~ 80 (70) Sample Rate 48 kHz 96 kHz 192 kHz Word Length 16 Bits 20 Bits 24 Bits Channels* SD0-L ~ SD03-L Freq. Mute 200Hz ~ 1600Hz (1000Hz) SD0-R ~ SD3-R Freq.
  • Page 18 TE460-137 User’s Guide HDR Emulator HDR Out AVI Colorimetry BT.2020 (1) BT.2020 (2) No Data ITU601 ITU709 xvYCC601 AVI Colorimetry xvYCC709 sYCC601 Adobe Y601 Adobe RGB EOTF [0] SDR Lumi Range [1] HDR Lumi Range [2] SMPTE ST2084.2 [3] Future EOTF Metadata Descr.
  • Page 19 TE460-137 User’s Guide Setup USB Port Power RS-232 OLED Contrast 0 ~ 8 Firmware Update Power Saving 2min ~ 10min EDID Reset Factory Restore Information [Unit Version Details] 400-0753-003...
  • Page 20 TE460-137 User’s Guide 7.7.3 OSD Menu - Cable Test (Menu Listings) Run Test Normal/Strict [Measured] (Enter- Start/Stop) Elapsed Time (Min:Sec) (PASS or FAIL result) Hotplug DOC Bus 4K6G AN Cable Setup Level Normal Strict Time 2 minutes 5 minutes 10 minutes...
  • Page 21 TE460-137 User’s Guide 7.7.4 Test Timings (Menu Listings) Timing 720×480p 720×576p 1280×720p 1920×1080i 1920×1080p 3840×2160p 4096×2160p 400-0753-003...
  • Page 22 TE460-137 User’s Guide 7.7.5 PC Resolutions (Menu Listings) PC Resolution Vertical Frequency (Hz) HDMI Input HDMI Output 640×350p 640×480p 59, 72, 75, 85 720×400p 70, 85 800×600p 56, 60, 72, 75, 85 848×480p 1024×768p 60, 70, 75, 85 1152×864p 70, 75, 85 1280×768p...
  • Page 23 TE460-137 User’s Guide 7.7.6 TV Resolutions (Menu Listings) Resolution Vert Freq HDMI Input HDMI Output 480i 59, 60 480p 59, 60 576i 576p 720p 25, 29, 30, 50, 59, 60 25, 30, 50, 60 1080i 50, 59, 60 50, 60...
  • Page 24 TE460-137 User’s Guide 7.7.7 Test Patterns (Menu Listings) Name Pattern Name Pattern Black Grayscale Blue Vert Lines Cyan Circle P12* Green Crosshatch P13* Crosshatch Magenta P14* Inverted Diagonal P15* Motion White P16* (grey bar moves) Yellow Multi-burst P17* Color Bar Patterns are full screen purity tests;...
  • Page 25 TE460-137 User’s Guide 7.8 RS232 Control RS232 commands are NOT case sensitive. Baud = 115k Data bits = 8 Stop bits = 1 Parity = None Flow control = none All commands start with dollar sign ($, 0x24) and end with carriage return (0x0D).
  • Page 26 TE460-137 User’s Guide Display audio frequency of channel. $audio_freq? SD0_L [SD0 Left Ch] audio_freq? SD0_L SD0_R [SD0 Right Ch] audio_freq? SD0_R SD1_L [SD1 Left Ch] audio_freq? SD1_L SD1_R [SD1 Right Ch] audio_freq? SD1_R SD2_L [SD2 Left Ch] audio_freq? SD2_L SD2_R [SD2 Right Ch]...
  • Page 27 TE460-137 User’s Guide Set the cable test level. $cable_level NORMAL cable_level normal STRICT cable_level strict Display the cable test level. cable_level? $cable_level? Display the cable test result. cable_result? $cable_result? Start/stop cable test. $cable_run START cable_run start STOP cable_run stop Display cable test status.
  • Page 28 TE460-137 User’s Guide $edid_model? Display EDID model/monitor name. > Read fail displays "$err_ddc" > Invalid EDID displays "$err_bad" RX [HDMI Input (Rx) Port] edid_model? rx SINK_H [HDMI Sink] edid_model? sink_h Set EDID name of the selected slot. $edid_name Slot C1 ~ C10,...
  • Page 29 TE460-137 User’s Guide Display the current EDID selection $edid_rx? edid_rx? for the unit’s HDMI input (Rx). Display EDID type of location. $edid_type? > Read fail displays "$err_ddc" > Invalid EDID displays "$err_bad" RX [HDMI Input(Rx) Port] edid_type? rx SINK_H [HDMI Sink] edid_type? sink_h Directly write an EDID block.
  • Page 30 TE460-137 User’s Guide $hdcp_in_ver Set HDCP version for HDMI input. V1.4 [HDCP v1.4 only] hdcp_in_ver v1.4 V1.4+V2.2 [HDCP v1.4 & v2.2] hdcp_in_ver v1.4+v2.2 Display the current HDCP version hdcp_in_ver? $hdcp_in_ver? used on the HDMI input. $hdcp_out_sw Enable/disable HDCP support on the HDMI output.
  • Page 31 TE460-137 User’s Guide $hdr_mfall Set the max HDR frame-avg light level. 0 ~ 65500 [100 unit increments] hdr_mfall 0 hdr_mfall 100 65500 hdr_mfall 65500 Display the current max HDR $hdr_mfall? hdr_mfall? frame-average light level. $hdr_sw Enable/disable HDR support on the unit’s HDMI output.
  • Page 32 TE460-137 User’s Guide Select the test pattern to output. $pattern 1 [Black] pattern 1 2 [Blue] pattern 2 3 [Cyan] pattern 3 4 [Green] pattern 4 5 [Magenta] pattern 5 6 [Red] pattern 6 7 [White] pattern 7 8 [Yellow]...
  • Page 33 TE460-137 User’s Guide Display current hot plug state $rx_hotplug? rx_hotplug? for the HDMI input (Rx). Set the hot plug time (in ms) for HDMI $rx_hotplug_t in (Rx). 50 ~ 500 [50ms steps] rx_hotplug_t 50 rx_hotplug_t 250 rx_hotplug_t 500 Display the current hot plug time (in ms)
  • Page 34 TE460-137 User’s Guide Display sink detect and information. $sink_detect? HOTPLUG [Sink’s hot plug status] sink_detect? hotplug RSENSE [Sink’s RxSense status] sink_detect? rsense HDCP [Sink HDCP status detection] sink_detect? hdcp HDCP_AKSV [Sink AKSV, hex (HDCP v1.4)] sink_detect? hdcp_aksv HDCP_BKSV [Rx BKSV, hex (HDCP v1.4)] sink_detect? hdcp_bksv HDCP_RXID [HDCP Rx ID, hex (HDCP v2.2)]...
  • Page 35 TE460-137 User’s Guide Displays source detection and information. $source_detect? 5V [5V detection state] source_detect? 5v (analyzer mode) HDCP [Source HDCP status detection] source_detect? hdcp HDCP_AKSV [Source AKSV, hex (HDCP v1.4)] source_detect? hdcp_aksv HDCP_BKSV [Rx BKSV, hex (HDCP v1.4)] source_detect? hdcp_bksv HDCP_RXID [HDCP Rcvr ID, hex (HDCP v2.2)]...
  • Page 36 TE460-137 User’s Guide ACR [Audio-Clock-Recovery packet status] source_detect? acr ACR_CTS [Audio-Clk-Recovery CTS value] source_detect? acr_cts ACR_N [Audio-Clk-Recovery N value] source_detect? acr_n ASP [status] source_detect? asp ASP_CH [channel number] source_detect? asp_ch audio sample ASP_FIFO [audio FIFO (error or normal)] source_detect? asp_fifo...
  • Page 37 TE460-137 User’s Guide Set mode to Analyzer, Pattern, or Cable. $task_mode CABLE [Cable Test Mode] task_mode cable ANALYSER [Analyzer Mode] task_mode analyser PATTERN [Pattern Mode] task_mode pattern Display the unit’s current operation mode. $task_mode? task_mode? Display the unit’s test timer day value.
  • Page 38 TE460-137 User’s Guide Display current output res. timing number. $timing? timing? Display current output resolution. $timingx? timingx? Set the video output format. $tmds_format HDMI tmds_format hdmi tmds_format dvi Display the current video output format. $tmds_format? tmds_format? Enable or disable video output.
  • Page 39 TE460-137 User’s Guide 7.9 Analyzer Information Examples 7.9.1 Deepcolor In Analyzer mode, you can find the deepcolor settings of the source signals by navigating the menus as follows: Analyzer Mode Main Menu Monitor Source Example Values Timing 3840x2160p24 HDCP Format v1.4...
  • Page 40 TE460-137 User’s Guide 8. Troubleshooting Guide We have carefully tested and have found no problems in the supplied TE460-137. However, we would like to offer suggestions for the following: TE460-137 Symptom Resolution Verify the cable between the transmitter input and the source is a genuine HDMI cable.