Advertisement
that the blue on/off switch is above the vacuum hose
connector. (fig.2.8)
5.10.
Align the ridges on the rim of the power head with the two side clasps. Place the upper part of each clasp over the ridges and snap the
clasps into place by pressing on the lower part of each clasp in turn. (fig.2.9)
5.11.
Align the arrow symbol on the large end of the vacuum hose with the pin on the front inlet of the drum. Push the fitting into the inlet and
lock in place by turning the fitting clockwise. (fig.2.10)
5.12.
Choose the desired nozzle and push it onto the telescopic suction tube. (fig.2.11)
6. DRY VACUUM CLEANING
WARNING! Ensure you read, understand and apply Section 1 'Safety Instructions'.
‰
Reminder: DO NOT vacuum hazardous substances. Use of an incorrect cartridge
filter will invalidate your warranty.
6.1.
Ensure the machine is unplugged from the power supply. (fig.3.1)
6.2.
Remove the power head and fit the locking cartridge filter down over the filter basket as
described in section 5.7.
6.3.
Reposition power head onto the drum body,clip in place. (fig.3.3)
6.4.
Insert the larger end of the flexible hose into the front inlet on the container and lock in
place. Push the required attachment onto the free end of the hose (fig.3.4). Plug in
power supply. fig.3.5)
6.5.
Switch to the 'On' (position 'I'). (fig.3.6)
6.6.
Switch to the 'Off' position ('0') when finished.
7. WET VACUUM CLEANING
WARNING! Ensure you read, understand and apply Section 1 'Safety
Instructions'. Reminder: Remove plug from power supply before opening
unit.
DO NOT vacuum solvents, explosives, inflammable and/or hazardous liquids
such as petrol, oil, spirits, paint, thinners, acids etc.
7.1.
Ensure the machine is unplugged from the power supply. (fig.4.1) Make sure the tank is
clean and free from dust and dirt.
7.2.
Remove the cartridge filter and fit a foam filter over the filter basket. (fig.4.2) Refit the
power head onto the drum.
7.3.
To the same flexible hose used in dry cleaning fit the desired nozzle (fig.4.3)
7.4.
Ensure the switch is 'Off' (position '0') before plugging into the power supply.
7.5.
Press the switch to 'On' (position 'I'). (fig.4.5)
NOTE: To vacuum large quantities of liquid, from a sink or tank etc, DO NOT immerse the
nozzle completely in the liquid, leave a gap at the top of the nozzle opening to allow an air
inflow. The machine is fitted with a float valve which stops the suction action when the tank
has reached its maximum capacity. The user will notice an increase in motor speed.
When this happens, turn off the machine, disconnect from power supply, remove the power
head from the container and empty the liquid into a suitable receptacle or drain (fig4.6).
To continue vacuuming, refit the power head and proceed. After wet vacuuming, turn the
machine off and unplug from power supply. Empty the container and clean and dry the
inside and outside before storage.
7.6.
Remember! After wet vacuuming the foam filter must be removed and a cartridge filter
must be fitted before dry vacuuming again.
WARNING! Not designed for liquid storage. Always empty liquids after
use and before storing.
8.
BLOWING
8.1.
Push the large end of the flexible hose into the blow connection in the top section. (fig.5.1)
8.2.
Ensure the power switch is turned off (fig.5.2) and plug in the power supply. (fig.5.3)
8.3.
Switch on the power (position 'I'). (fig.5.4)
8.4.
The unit will now blow through the hose and can be used to clear obstructions within the pipe. (fig.5.5)
WARNING! If after a few seconds the hose is still blocked turn of the unit and clear
the hose manually.
9. MAINTENANCE
9.1.
GENERAL MAINTENANCE.
9.1.1.
Ensure the machine is unplugged from the power supply.
9.1.2.
Disconnect the hose from the container.
9.1.3.
Undo the clasps and remove power head from the container.
9.1.4.
Clear out any dirt or debris from the container and hose.
9.1.5.
Clean the foam filter by washing it in a mild soapy solution.
9.1.6.
Check that the telescopic suction tube operates smoothly
and check the power cable to make sure has not received any
damage.
© Jack Sealey Limited
Original Language Version
fig.3
fig.4
fig.5
PC200SD.V3 Issue 4 (4,F) 08/09/20
Advertisement
