Summary of Contents for Hydro-Force Hydro-Well III
- Page 1 Revised: 01/09/2020 LMANAX139 1609-8636 HYDRO-WELL III 100 GALLON FRESH WATER TANK Hydro-Force Manufacturing 4282 South 590 West Salt Lake City, UT 84123 801-268-2673 801-268-3856 FAX...
- Page 2 Congratulations on your purchase of the Hydro-Well III 100 gallon water tank. Years of experience, engineering, and planning have gone into the design and manufacturing of the Hydro-Well III. We take a great deal of pride in the Hydro-Well III; our goal is no less than your complete satisfaction.
-
Page 3: Specifications
Vehicle Requirements & Preparation The vehicle must have a cargo capacity to handle the weight of the Hydro-Well III as well as the weight of more than 100 gallons of water. A Hydro-Well III, when full of water, can weight more than 1000lbs. -
Page 4: Tank Preparation
Tank Preparation WATER INLET FITTING - The Hydro-Well III gives you the option of mounting the water inlet fitting on the top of the tank on either the right or left side of the tank. Choose the location on the top right or top left side of the tank that best suits your layout and to install the Float Valve Assembly inside the tank. - Page 5 WATER OUTLET FITTING - The Hydro-Well III gives you the option of mounting the water outlet fitting on the bottom back of the tank toward the right or left side of the tank. Choose the location that best suits your layout and to install the water outlet fittings on the bottom of the tank.
- Page 6 The other Vent/Overflow port can be blocked with the PVC 1/2” Hex Plug (BR226P) included with the Hydro-Well III. The ¾” ID hose & hose clamp are not included with the Hydro-Well III. Overflow Port – Right Side 1/2” 90° Elbow M-F – BR286 3/4”...
-
Page 7: Tank Installation
Before drilling through floor, always check under the vehicle to locate beams and vehicle components such as the gas tank, fuel lines, wiring harnesses, heat shields, spare tire, etc. Position the Hydro-Well III so all required holes can be drilled through floor without damaging vehicle components and bolts are positioned with room to attach mounting plates, washers and nuts for safe and secure mounting. - Page 8 Once you have checked for obstacles under the vehicle & determined the correct hole positions, drill 3/8” holes for each bolt & hold down rod. Use a drill bit depth stop or shield if needed to prevent going through too far and damaging vehicle components. Thread 3/8”...
- Page 9 Place a 3/8” flat washer ⑪on each of the four 3/8” tap bolts ③and insert the bolts through holes in floor bracket ⑧. Two bolts & washers on each floor bracket on each end of the tank. Under the van, place back-up plate ⑬ on each bolt and secure to floor using the 3/8” lock washer ⑩...
-
Page 10: Optional Parts And Accessories
Optional Parts & Accessories Inlet Parts: PAF01 3/8” MALE QUICK CONNECT BRASS PAF02 3/8” FEMALE QUICK CONNECT BRASS BR136 REDUCING HEX NIPPLE ½” X 3/8” BRASS BR327 ADAPTER ¾” FGH X ½” FPT BRASS BR076 NIPPLE ½” HEX BRASS Outlet Parts: AH66 ¾”... - Page 11 Part # Hydro-Well III Parts Description TANK HYDRO-WELL III RAW NM5803 (Includes - NM4267 Bulkhead fittings) BRACKET TIE DOWN REAR NM5802 NM5812 BOLT TAP 3/8-16 x 3” ZINC PLTD NM5808 NUT COUPLING 3/8-16 GRADE 2 ZINC PLTD ROD THREADED 3/8-16 x 36” ZINC PLTD...
- Page 12 Hydro-Well III Parts...
- Page 13 Hydro-Well III Parts Attachment detail under Van floor...
- Page 14 *Indicates item is not included Hydro-Well III Parts with Hydro-Well III *REDUCING NIPPLE ½” X 3/8” #23 ELBOW 90 DEG ½” M-F *3/8” MALE QUICK CONNECT #24 BULKHEAD FITTING ½” #23 ELBOW 90 DEG ½” M-F #22 BARB ¾” X ½” MPT *HOSE CLAMP PH09 *¾”...
-
Page 15: Float Valve Assembly
Hydro-Well III Parts #20 NIPPLE ½” X 4” SS #19 FLOAT VALVE – ½” FPT INLET #27 THREADED ROD 1/4-20 X 1-3/4” SS #25 ELBOW 90º F-F BRASS #28 NUT 1/4-20 HEX SS TANK VENT / OVERFLOW PORT #26 FLOAT BALL 4” X 5” POLY *PRESSURE REGULATOR –... -
Page 16: Limited Warranty
LIMITED WARRANTY Your Hydro-Well III is designed to give you years of reliable service. If a problem should arise contact your distributor or Hydro Force for assistance. Hydro Force warrants the Hydro-Well III to be free from defects in material or workmanship for three years / 36 months from the date of purchase.
Need help?
Do you have a question about the Hydro-Well III and is the answer not in the manual?
Questions and answers