Advertisement
3. SPECIFICATION
Model No:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HVF20P
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111W
Speeds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Fan Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ø550mm(20")
Maximum Airflow: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138mtr³/min
Speed Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100/1250/1350rpm
Current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5A
Height:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1300-1410mm
4. ASSEMBLY
4.1.
Fit the fan to the motor shaft by tightening the grub screw onto the machined flat (fig.1).
4.2.
Connect the front fan guard to the rear fan guard by screwing through the locations using the 6 screws
supplied (fig.2).
4.3.
Bolt the outer tubular stand to the base using the fixings supplied.
4.4.
Slide the inner tubular stand into the outer tubular stand, fit and tighten the column lock to hold at the
required height.
4.5.
Connect the semi-circular yoke to the inner tubular stand by means of the connector (fig.3) using the
nuts, bolts and washers supplied.
4.6.
Locate the motor housing and rear guard into the yoke and fix in place using the nuts, bolts and
washers supplied.
4.7.
Slide the fan onto the shaft and tighten the fixing screw.
5. OPERATION
IMPORTANT: Ensure that all safety instructions from section 1 have been read and understood before using the fan.
5.1.
Set the fan on a level, dry surface.
5.2
Plug the power cord into the mains supply.
5.3.
The fan features 3 speeds - selectable using the switch located at the back of the fan. The fan speed increases as the switch is turned
in a clockwise direction.
5.4.
Adjust the direction of air flow up or down by loosening the nuts which secure the fan assembly to the yoke and tilting the fan assembly
to the required angle and then tightening the nuts. To adjust the height setting, loosen the column lock, set at the desired height and
then re-tighten.
5.5
When not in use, disconnect from power supply and store in a safe, dry, childproof location.
6.
MAINTENANCE
▲
IMPORTANT: Turn the control switch to OFF and disconnect the fan from the power supply before cleaning.
6.1.
Use only a soft, damp cloth to clean the fan.
6.2.
DO NOT submerse the fan in water and NEVER allow water to drip into the motor housing.
6.3.
DO NOT use solvents or other chemicals to clean the fan.
6.4.
To clean the fan blades, remove the 6 screws around the guards and then lift off the front guard from the top hook.
6.5.
Wipe the blades and guards.
6.6.
Reassemble by hooking the front guard into place at the top of the rear guard and then replace the 6 screws so that they engage both the
front and rear guards.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
01284 703534
sales@sealey.co.uk
Original Language Version
fig.1
fig.1
fig.2
fig.3
www.sealey.co.uk
HVF20P.V2 Issue: 1 - 08/11/17
Advertisement
