Advertisement
Quick Links
Honda CBR250R (11-12) DIY Windscreen Install
Installation Manual for Honda CBR250R
Thank you for purchasing Zero Gravity windscreen, which has
been designed and manufactured to give years of safe & fun rid-
ing. These instructions give you an in-depth look at the installation process. To receive further assistance or parts, please call Zero
Gravity
®
Sales Department at 805-388-8803 or E-mail at
Helpful hints: Use metric tools, clean hands, put the bike on a center stand. Do not pry on the screen excessively, as it will
break without much warning.
Removing Factory Screen Over View / Remove side mirrors
Overview of screen and exploded view of assembly. It
might be a good idea to go get a 2nd helper with the
install. Remove side mirrors, set aside.
Side Fairing Screw Locations Part 1 of 3
Here's the side fairing screw location, there are two
more locations after this.
Note:
Side Fairing Screw Locations Part 3 of 3
Here's the inner front cowl of the bike, side fairing
screw location.
Note:
A screw is used.
Tel: 800-345-9791
912-A Pancho Road • Camarillo, CA 93012
salesinfo@zerogravity-racing.com
B screws are used.
PLEASE READ BEFORE
MOUNTING YOUR WINDSCREEN
A
Remove Side Fairing (For both sides)
Remove 2 sets of allen screws A & B .
"A" is longer and has a step on the bottom shoulder.
Side Fairing Screw Locations Part 2 of 3
Here's the bottom of the bike, side fairing screw loca-
tion. There is one more location after this.
B screws are used.
Note:
Pulling the Side Fairing / Retention Clip Locations
Here's the retention clips location after pulling the side
fairing off. Outline in white boxes.
wires are connected to the side fairing.
Fax: 805-388-8285
install 443-IS
.
B
Note:
One bolt
Caution:
Electrical
1
Advertisement
Summary of Contents for ZERO GRAVITY SR Series
- Page 1 Honda CBR250R (11-12) DIY Windscreen Install Installation Manual for Honda CBR250R PLEASE READ BEFORE Thank you for purchasing Zero Gravity windscreen, which has MOUNTING YOUR WINDSCREEN been designed and manufactured to give years of safe & fun rid- ing. These instructions give you an in-depth look at the installation process. To receive further assistance or parts, please call Zero salesinfo@zerogravity-racing.com...
- Page 2 install 443-IS Honda CBR250R (11-12) DIY Windscreen Install Pinch both sides Feed the wire loom into hole. Attaching and Detaching Wires Detaching Wire Loom Keeper Detach the fairing wires and set side fairing aside. Dislodge the keeper by using a needle nose pliers Note: Upon reattaching wires, match the wire colors.
- Page 3 install 443-IS Honda CBR250R (11-12) DIY Windscreen Install Point it 5 Point it 7 O’clock O’clock Front Fairing Headlamp Removal Access To Inner Front Face Fairing OVERVIEW 1 of 2 You will be removing these Small screws from, the front upper fairing, shown in a Circle. You will be removing these Big screws from, the front upper fairing, shown in a Box.
- Page 4 install 443-IS Honda CBR250R (11-12) DIY Windscreen Install Pull up on the fairing to dislodge from these holes. Front Fairing Headlamp Removal Access To Inner Front Face Fairing PT1 Front Fairing Headlamp Removal Access To Inner Front Face Fairing PT2 Cover your front fender with a cloth.
- Page 5 install 443-IS Honda CBR250R (11-12) DIY Windscreen Install FRONT BIKE Access Opening Headlamp Dowel Headlamp side Mount Side and Front Fairing Removal Side and Front Fairing Removal Once all of the fairing screws are removed place the Pull the side and front fairing away from the headlamp headlamp dowel into the rubber grommet on either side and be sure to route the headlamp side mount to the of the bike as shown.
- Page 6 Once removed look at OVERVIEW 1 of 2 image and remove the screws. Then carefully pop these out, outlined in white cir- cle and replace it with a Zero Gravity Windscreen. Follow the instructions carefully in reverse, there are a few steps below to guide with the install.