Panasonic SC-UA7 Owner's Manual page 17

█
Unit displays
"ADJUST CLOCK"
•
The clock is not set. Adjust the clock.
"ADJUST TIMER"
•
The play timer is not set. Adjust the play timer.
"AUDIO UNSUPPORTED"
•
The signal format or frequency is not supported.
•
This system does not support bitstream signals. Change
the digital audio output setting on the external equipment
to PCM.
•
This system supports sampling frequencies of 32 kHz,
44.1 kHz and 48 kHz. Select only the supported sampling
frequencies on the connected equipment.
•
Try connecting the external equipment by using the
auxiliary input.
"AUTO OFF"
• The system has not been used for 20 minutes and will turn
off within a minute. To cancel, press any button or touch
any touch key.
"ERROR"
• An incorrect operation was done. Read the instructions and
try again.
"F61"
•
There is a problem with the amplifier of the system.
•
Disconnect the USB device. Turn off the system and then
turn on again.
"F703"
•
Examine the Bluetooth ® connection.
•
Disconnect the Bluetooth
then turn on again.
"F76"
•
There is a problem with the power supply.
•
Disconnect the AC power supply cord and consult your
dealer.
"F77"
• Disconnect the AC power supply cord and consult your
dealer.
"NO PLAY"
"UNSUPPORT"
• Examine the content. You can only play supported format.
•
The system may have a problem. Turn off the system and
then turn on again.
"NO TRACK"
•
There is no album or track in the USB device.
"PLAYERROR"
•
An unsupported MP3 file has been played. The system will
skip that track and play the next one.
"REMOTE 1"
"REMOTE 2"
•
The remote control and the unit are using different codes.
Change the code of the remote control.
–
When "REMOTE 1" is shown, press and hold [OK] and
[1] for a minimum of 4 seconds.
–
When "REMOTE 2" is shown, press and hold [OK] and
[2] for a minimum of 4 seconds.
device. Turn off the system and
®
"USB A NO DEVICE"
"USB B NO DEVICE"
•
The USB device is not connected. Examine the connection.
"USB OVER CURRENT ERROR"
•
The USB device is using too much power. Disconnect the
USB device, turn off the system and then turn on again.
"VBR"
•
The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [RADIO/EXT-IN] to select "AUX 1" or "AUX 2".
█
To set the code to "REMOTE 2"
1
Touch and hold [SELECT] on the unit and [2] on
the remote control until "REMOTE 2" is shown.
2
Press and hold [OK] and [2] for a minimum of
4 seconds.
█
To set the code to "REMOTE 1"
1
Touch and hold [SELECT] on the unit and [1] on
the remote control until "REMOTE 1" is shown.
2
Press and hold [OK] and [1] for a minimum of
4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed or
when touch keys are touched.
• You want to clear and reset the memory content.
1
Touch and hold [1] on the unit until "RESET?" is
shown.
2
While you touch and hold [1] on the unit, touch
[SELECT].
"RESET" is shown.
After "– – – – – – – – –" is shown, the unit will turn off
automatically.
All the settings are set back to the factory defaults.
It is necessary to reset the memory items.
17