Summary of Contents for Cub VS-95A043
- Page 1 BLIND SPOT DETECTION SYSTEM User Manual & Installation Guide VS-95A043 For Passenger Cars Blind Spot Detection Lane Change Alert...
-
Page 2: Table Of Contents
Contents Precautions ......................2 Introduction ......................5 ........................ 5 System block ..................5 Product specifications Installation Guide ..................6 ....................6 Installation diagram ....................6 Package contents ....................... 7 Installation steps ....................... 9 Reinstallation User Manual ....................... 10 ................10 System startup and shut off ...................... -
Page 3: Precautions
Precautions Blind Spot Detection System Before using this device, please read this instruction manual carefully before installing or removing it to ensure that the device is safe to use. The Company shall not be liable for any damage arising from failure to comply with the following matters. - Page 4 If the connector is Please do not pull the Please do not pull dislocated, please connector apart by the harness by force. replace the connector pulling the harness. to its original position. Connect the connector Cut off the excessive and terminal tightly. length of the cable tie.
- Page 5 NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
-
Page 6: Introduction
Introduction Blind Spot Detection System Thank you for purchasing this device. The device uses a 77 GHz millimeter-wave radar to detect vehicles coming behind your car. When there is a car getting in the detection zone, the device will provide visual and audible warnings to remind you to pay attention to the car in order to protect the safety of the driver and passengers. -
Page 7: Installation Guide
Installation Guide Blind Spot Detection System 3-1 Installation diagram Left turn signal Left indicator Buzzer Cigarette lighter plug Radar / IGN WIRING Right turn signal Right indicator 3-2 Package contents Item Q' ty Radar with its bracket 1 set Indicator 2 pcs Buzzer 1 pcs... -
Page 8: Installation Steps
Tear off the tape on the radar's bracket, face the surface printed with the logo Cub outwards, and attach the bracket parallel and close to the ceiling or align along the defog line. Be careful not to attach it to the defog line. - Page 9 Note: Please ensure the positive electrode of the left and right turn signals by a multimeter. Note: If the turn signals are not connected, the system will alarm by illuminating indicators only. After connecting the radar and main power harness, hide the wires along with the ceiling to the C-pillar on the driver side, and connect the left and right turn signal wirings to the car's left and right turn signal trigger wires(+) with crab clips.
-
Page 10: Reinstallation
Right indicator goes to right side A-pillar through the left side A-pillar and then the ceiling. The installation height and method is the same with the left one. Please ensure to hide all the wires properly into the trims and frame's waterproof strips to avoid the wiring harness from affecting driving safety, and obstructing you from getting in and off the car. -
Page 11: User Manual
User Manual Blind Spot Detection System 4-1 System startup and shut off 4.1.1 System startup When ACC is ON, the indicator will illuminate for 3 seconds, and the buzzer will chime once, indicating that the system starts normally. Note: The system self-tests within 10 seconds after power-on, and using the turn signals or hazard warning lights in this period time would lead to the indicators flashing, which means the system reads the turn signals correctly. -
Page 12: Detection Zone
4.2.1 Detection zone LCA 20m LCA 20m 4.2.2 Blind Spot Detection (BSD) When a vehicle approaches your car from behind and enters the detection zone, extending rearward from the radar to approximately 7 m, the corresponding indicator will illuminate. If the corresponding turn signal is ON, the system not only light up the indicator, but also sound an audible alert. -
Page 13: System Abnormalities
If the corresponding turn signal is ON, the system not only light up the indicator, but also sound an audible alert. Note: If the turn signals are not connected, the system will alarm by illuminating indicators only. LCA 20m 4-3 System abnormalities 4.3.1 Malfunction prompts If the system malfunctions, the buzzer will sound an audible alert for 3 seconds for every 10 minutes. - Page 14 Abnormal Possible Item Possible solution Status Causes Re-plug the connector and check if the indicator The indicator Damaged can light up or not. If does not light connector or it still does not light poor contact up, please contact the power on dealer self -...
- Page 16 www.cubelec.com.tw E-mail: adasinfo@cubelec.com.tw Address : NO.6, LANE 546, SEC.6, changlu RD., fuhsin township, changhua county 50648, taiwan(R.O.C.)
Need help?
Do you have a question about the VS-95A043 and is the answer not in the manual?
Questions and answers