Hanwest HAN-L62 User Operating Instructions

7 DAY PROGRAM TIME CONTROL

ON
1) Press "PROGRAM" and 1 will appear to indicate the 1st power on time is
ready to be set. You will notice "OPERATION" – "ZONES" – "SET TEMP POINT"
– "FAN SPEED" and "7 DAY PROGRAM TIME CONTROL" all flash.
2) Press "MODE" to select desired mode.
3) Press zone buttons to select zones to be turned on.
4) Press "SET TEMP UP" or "SET TEMP DOWN" to select desired temperature.
5) Press "FAN SPEED" to select desired speed.
6) Press "WEEK" to select the desired day/s that you want your power-on time.
7) Press "HOUR", then "MINUTE" to enter the first desired power-on time. (Note: To reset times, press
"RESET/RECALL").
ON
8) When desired power on (1 ) details are entered, press "PROGRAM". 1
indicate the 1st power off time is ready to be set.
9) Repeat steps 6-8. (Note: For every power-on time, there must be a power-off time).
10) Repeat steps 1-10 until the 6th power-off timer is set. (Note: There is a max of 6 ON/OFF times).
11) You may press "PROGRAM" to double check the days and times.
12) Press "CLOCK" to resume present time.

OPTIONAL MULTIPLE CONTROL

If more than 1 control is installed, you can select any control to be the "MASTER" by simply pressing the
ON/OFF button. All other controls will change to "SLAVE" mode automatically.
To adjust each control to desired settings, simply follow instructions from the previous pages.
In the event of a power failure, the master control will be the one prior to the power failure that will resume
operation.
MULTIPLE SENSORS (AVERAGING)
If optional multiple sensors are connected (up to 4 in total) they are activated by pressing the
relevant ZONE buttons
(1 to 4).
DIAGRAM OF HAN-L62 WITH FRONT DOOR OPEN
COUNT DOWN
TIMER DISPLAY
MASTER
SLAVE
CLEAN
KEYLOCK
1
SET TEMPERATURE &
2
ROOM TEPERATURE
3
4
DISPLAY
ON/OFF BUTTON
MODE SELECT
TEMPERATURE UP
SET TEMP.
SET TEMP.
TEMPERATURE DOWN
ROOM
DISPLAY ROOM TEMP
TEMP.
Sleep OPERATION SLEEP
COUNT DOWN TIMER
FILTER RESET
FAN SPEED SELECT
OFF
MODE DISPLAY
SLEEP & FILTER
CLEAN DISPLAY
12H TIMER OPERATION COOL ON HEAT ON ZONES
FAN DRY
DEFROST DEICE 1 2 3
ZONE DISPLAY
COOLING
HR
SLEEP FAULT
HEATING
4 5 6
AUTO PROGRAM TIME SET
SET TEMP POINT FAN SPEED 7 DAY PROGRAM TIME CONTROL
HIGH Mon Tue Wed Thu Fri Sat Sun
° C MEDIUM
ON TIME & PROGRAM DISPLAY
ON
LOW
AM
° F AUTO
CONSTANT
ROOM TEMP OFF PM OFF
FAN SPEED DISPLAY
ON OFF
HAN-L62
MODE CLOCK RESET
RECALL
SET TIME & PROGRAMS
7 DAY - 6 PROGRAM TIMER
FAN
WEEK HOUR MINUTE
SPEED
12H OFF
ZONE1 ZONE2 ZONE3
TIMER
ZONE SELECT
CLEAN
ZONE4 ZONE5 ZONE6
RESET
HAN-L62 MICROPROCESSOR CONTROLLER
will now appear to
Your air conditioner is supplied with the latest advanced process
Model HAN-L62 Microprocessor Controller.
The adjustment details for this easy to use control are described in
this booklet.
All control settings for the HAN-L62 can be changed whether the
control is turned off or on.
When adjusting the control the backlight in the display panel is
turned on and switches off after the last adjustment is made.
If the power to the unit is turned off or a power failure occurs all last
settings are maintained in EEPROM memory. The real time clock
operation is backed up by a long life battery.
USER'S OPERATING INSTRUCTIONS