Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Openpath V1.4
Summary of Contents for Openpath V1.4
- Page 1 OPENPATH SINGLE DOOR CONTROLLER INSTALLATION GUIDE V1.4...
- Page 2 Openpath Single Door Controller Installation Guide GETTING STARTED ADDITIONAL RESOURCES PRIOR TO INSTALLATION Installation NETWORK REQUIREMENTS POWER REQUIREMENTS SELECTING A BACKUP BATTERY MOUNTING INSTRUCTIONS RECOMMENDED CONFIGURATION STANDARD WIRING CONFIGURATION WIRING FAIL SAFE AND FAIL SECURE LOCKING HARDWARE VOLTAGE SWITCHES PROVISIONING THE SDC...
-
Page 3: Getting Started
Openpath Single Door Controller Installation Guide GETTING STARTED This Installation Guide explains how to install and configure the Openpath Single Door Controller (SDC) as part of an Openpath Access Control system. ADDITIONAL RESOURCES Smart Reader Data Sheet ● Openpath Admin App Guide ●... -
Page 4: Power Requirements
NAT device is not required. POWER REQUIREMENTS The Openpath SDC can be powered with PoE, PoE+, or an external 12-24V supply. Use an external power supply for backup or if PoE is not available—24V required if locking hardware requires 24V. - Page 5 Figure 1: Mounting SDC to wall To install on drywall: Use the provided drywall screws (C) and anchors (not shown) to attach backplate (B) to wall 2. Snap on main housing (D) to backplate (B) Version 1.4 © Openpath 2020 Page 5...
-
Page 6: Recommended Configuration
Note: For elevators, all relays and readers must be connected to the same SDC. If you need more than two access controlled floors or readers, add the Openpath Elevator Expansion Module. - Page 7 WIRING FAIL SAFE AND FAIL SECURE LOCKING HARDWARE Fail safe and fail secure are ways of configuring locking hardware: ● Fail safe hardware unlocks when power is interrupted ● Fail secure hardware locks when power is interrupted Version 1.4 © Openpath 2020 Page 7...
- Page 8 Provisioning the SDC means registering it in the Control Center and getting it up and running with the latest firmware. You can provision the SDC using the Open Admin app for first time setup and in the case of RESETTING THE SDC. Version 1.4 © Openpath 2020 Page 8...
- Page 9 Note: If you’re provisioning SDCs for a customer account, the customer org will need to be created by Openpath first. REQUIREMENTS ● Meet all NETWORK REQUIREMENTS ● Connect the SDC to the Internet via Ethernet or via Wi-Fi ● Install the Open Admin app iOS App Store ○...
-
Page 10: Provisioning Steps
Openpath 4-Port Expansion Openpath 8-Port Expansion iii. Openpath 16-Port Elevator d. Click Next 5. Enter how many Readers are connected to the SDCs and enter names. Click Next. 6. Review your Site Details, then click Confirm & Submit. It may take a few minutes for setup to complete. - Page 11 Go to the Hardware Dashboard in the Control Center and restart the services listed under Remote Diagnostics. If this doesn’t work, power cycle the SDC (remove power, wait 10 seconds, apply power). If the error persists, contact Openpath support. Version 1.4 © Openpath 2020...
-
Page 12: Test Internet Connection
Ethernet and Wi-Fi connections can be DHCP (default) or can have a static IP address. To change network settings: Connect to the SDC by pressing the Admin button again if needed Tap on Network Settings Select Configure network manually Configure the network settings as needed Version 1.4 © Openpath 2020 Page 12... -
Page 13: Country Settings
SDC LEDS RESETTING THE SDC LEGACY WIRING SDC LEDS The Openpath SDC’s Status LED indicates the following: Solid White indicates the SDC is provisioned and functioning normally Blinking Red indicates there is a problem with the Internet connection Version 1.4 ©... - Page 14 Admin app Solid Red indicates the SDC is in an error state–refer to Troubleshooting the SDC The Openpath SDC has eight port LEDs and two power LEDs. The port LEDs indicate the following: ● Openpath Readers or Wiegand Readers ○ Solid: Normal operation Version 1.4...
- Page 15 HARD RESET WARNING: Only hard reset the SDC if absolutely necessary and if instructed by Openpath. This will clear all of the data off of the SDC and will require reprovisioning. To hard reset the SDC: Remove power from the SDC 2.
- Page 16 22-6) results in slower connections and dropped packets between the Openpath Reader and SDC. To remedy this, you can switch GND and VIN with +B and -A connections on the SDC and readers to ensure the data pair (+B and -A) are using the alternate pair of legacy wires.
- Page 17 L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Version 1.4 © Openpath 2020 Page 17...
- Page 18 Warnings ● Disconnect power before servicing ● Do not plug into an outlet controlled by an on/off switch Technical Specifications Table 2: Technical specifications of Openpath hardware Smart Readers (OP-RLF-STD, 12VDC, 0.25A OP-RHF-STD, OP-RLF-MULB, OP-RLF-STD/MULB: FCC ID: 2APJVOPRLF OP-RHF-MULB) OP-RHF-STD/MULB: FCC ID: 2APJVOPRHF Elevator Board (OP-16EM) 12-24VDC, 0.35A @ 12V, 0.2 @ 24V...
Need help?
Do you have a question about the V1.4 and is the answer not in the manual?
Questions and answers