Table of Contents
Advertisement
Quick Links
Regency Plateau
Decorative Gas Appliance
WARNING:
If the information in these instructions
are not followed exactly, a fire or
explosion may result causing property
damage, personal injury or loss of life.
WARNING: For Outdoor Use Only.
Installation and service must be
performed by a qualified installer,
service agency, or the gas supplier.
WARNING:
Do not store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or any
other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appli-
ance.
Tested by:
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
920-280
PTO30 Outdoor
®
DANGER - FIRE OR EXPLOSION HAZARD
If you smell gas:
• Shut off gas to the appliance.
• Extinguish any open flame.
• If odour continues, leave the area immediately.
• After leaving the area, call your gas supplier or fire
department.
Failure to follow these instructions could result in fire or
explosion, which could cause property damage, personal
injury, or death.
Installer: Leave this manual with the appliance.
Consumer: Retain this manual for future reference.
Owners &
Installation Manual
Models: PTO30-NG11 / PTO30-LP11
www.regency-fire.com
05.13.21
Advertisement
Table of Contents
Related Manuals for Regency Fireplace Products Plateau PTO30
Summary of Contents for Regency Fireplace Products Plateau PTO30
- Page 1 Owners & Regency Plateau PTO30 Outdoor ® Installation Manual Decorative Gas Appliance Models: PTO30-NG11 / PTO30-LP11 www.regency-fire.com WARNING: DANGER - FIRE OR EXPLOSION HAZARD If the information in these instructions If you smell gas: are not followed exactly, a fire or •...
- Page 2 To the New Owner: Congratulations! You are the owner of a state-of-the-art Outdoor Decorative Gas Appliance by REGENCY . The Plateau PTO30 Outdoor ® ® decorative gas appliance has been designed to provide you with all the warmth and charm of a fire at the flick of a switch. The Plateau PTO30 Outdoor Decorative Gas Appliance has been approved by Warnock Hersey/Intertek for both safety and ®...
-
Page 3: Table Of Contents
table of contents Copy of Safety Decal .............4 Aeration Adjustment ............22 PTO30 Decal Location ..........4 PTO60 Assembly ............23 PTO30 Wall Switch and Battery Installation (included with unit) ............24 PTO60 Wall Switch and Battery Installation DIMENSIONS (included with unit) ............25 PTO30/PT060 Drain Installation (Recommended) ..26 PTO30 Unit Dimensions ..........5 Glass Crystal/Basalt Volcanic Stones Installation ..27 PTO60 Unit Dimensions ..........6... -
Page 4: Copy Of Safety Decal
safety decal This is a copy of the label that accompanies each PTO30 Outdoor decorative gas appliance. We have printed a copy of the contents here for your review. NOTE: Regency units are constantly being ® improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. -
Page 5: Dimensions
dimensions PTO30 UNIT DIMENSIONS Gas Connection/Electrical connections if using optional Hardwire Kit. ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY. ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS. Regency Plateau PTO30-11 Outdoor Gas Fireplace ®... -
Page 6: Pto60 Unit Dimensions
dimensions PTO60 UNIT DIMENSIONS NOTE: PTO60 is two PTO30 units assembled end to end (see PT060 assembly for more details). 66-7/16" (1688mm) TOP VIEW Gas Connection/Electrical connections if using optional Hardwire Kit 8-1/4" (210mm) SIDE VIEW END VIEW Regency Plateau PTO30-11 Outdoor Gas Fireplace ®... -
Page 7: Important Message
installation IMPORTANT MESSAGE 3. See general construction and assembly instruc- DO NOT USE THIS APPLIANCE IF tions. The appliance should be enclosed. SAVE THESE ANY PART HAS BEEN UNDER WATER. IMMEDIATELY CALL A QUALIFIED 4. Inspect the burner before each use of the appli- INSTRUCTIONS ance for blockage and any signs of deterioration. -
Page 8: Installation Checklist
installation LOCATING YOUR INSTALLATION OUTDOOR DECORATIVE GAS APPLIANCE CHECKLIST 1. When selecting a location for your decorative gas appliance, ensure that the clearances are met. If installing as PT060 (2 x PT030 end to end) you must repeat steps 2 - 5 for both units. 2. -
Page 9: Important Information For Outdoor Fireplace Installations
installation IMPORTANT INFORMATION FOR OUTDOOR FIREPLACE INSTALLATIONS IMPORTANT THINGS TO REMEMBER • Never insulate around the body of the unit • Excessive heat retention in the firebox will lead to component failure • Correct Working Gas pressure is critical on “E” units and fireplace malfunction •... -
Page 10: Minimum Clearances To Combustibles
installation MINIMUM CLEARANCES TO COMBUSTIBLES The clearances listed below are minimum distances unless otherwise stated. A major cause of fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this decorative gas appliance be installed only in accordance with these instructions. WARNING Caution Requirements Fire hazard is an extreme risk... -
Page 11: Inner Framing Dimensions (Required)
installation INNER FRAMING DIMENSIONS (REQUIRED) NOTE:FRAMING MATERIAL NOT SUPPLIED PTO30 37-15/16" (964mm) NOTE: Framing materials must be non-combustible when used within 4" of the unit. Combustible framing materials may be used outside the 4" clearance range. Finishing materials MUST be non-combustible. Consideration should be given to weather / elements when choosing framing materials (ie. -
Page 12: Enclosure Vent Installation
installation PTO30/PTO50 OUTDOOR SERIES ENCLOSURE VENT INSTALLATION PTO30/PTO50 ENCLOSURE VENT INSTALLATION PTO30/PTO50 - Two (2) ventilation grills are required for all enclosures. The ventilation grill(s) must be placed at either end as shown to allow the air to circulate from one end to the other. This is to alleviate moisture and allow for air to circulate. Minimum recommended size 20" sq (508 mm²) ea. PTO60/PTO80/PTO100 - Four (4) ventilation grills are required for all enclosures. -
Page 13: Optional Hard Wire Kit Installation
installation OUTDOOR SERIES OPTIONAL HARD WIRE KIT INSTALLATION OPTIONAL HARD WIRE KIT INSTALLATION A hard wire kit is available for this unit as an option, to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the household wiring. - Page 14 OUTDOOR SERIES installation 5. Plug in the supplied AC adaptor and run the wire through the bottom 10. HZO42/HZO60--Remove the burner tray by lifting up and out. of the outer box, be sure to use a grommet to protect the wire. 6.
- Page 15 OUTDOOR SERIES installation 919-774 04.03.17 Regency Plateau PTO30-11 Outdoor Gas Fireplace ®...
-
Page 16: Pto30 Wiring Diagram (Battery Operation)
installation PTO30 WIRING DIAGRAM (BATTERY OPERATION) This appliance does not require a 120V A.C. supply for operation. NOTE: 4 AA batteries must be installed in the battery pack to operate the burner switch. Do not use a 9 volt battery. 0.886.001 Proflame Valve Standard Main On/Off Switch... -
Page 17: To30 Wiring Diagram Using Ac Adaptor
installation PTO30 WIRING DIAGRAM USING AC ADAPTOR 0.886.001 Proflame Valve Standard Main On/Off Switch 1 of 10 or Optional Wall Switch 0.584.622 PTO60 WIRING DIAGRAM (TWO PTO30S ASSEMBLED END-TO-END) USING AC ADAPTOR Spark Electrode Sense Electrode 0.886.001 Proflame Valve 1 of 10 1 of 10 0.584.622 0.584.622... -
Page 18: Ac Adaptor Installation
installation OUTDOOR SERIES AC ADAPTOR INSTALLATION AC ADAPTOR INSTALLATION A hard wire kit is available for this unit as an option (see hard wire kit instructions), to hard wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the household wiring. This appliance must be electrically connected and grounded in accordance with local codes, if hard wired. -
Page 19: Lp Conversion
installation PTO30 / PTO30-1 LP CONVERSION CONVERSION FROM NG TO LP THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Each Kit contains one LP Conversion Kit 5. L ocate and remove 9 screws to remove the burner tray. Conversion Kit # 376-969 Contains: Qty. - Page 20 PTO30 / PTO30-1 installation 7. Remove burner orifi ce with a 1/2" wrench. Use another wrench to 11. Remove 6 screws on valve access cover. hold on to the elbow behind the orifi ce. Discard orifi ce. Install new NG orifi ce supplied with kit. Repeat steps to install LP orifi...
-
Page 21: Finishing
installation FINISHING Side nailing strips are adjustable for material from a minimum of 1/2" thick FINISHING MATERIALS: up to a maximum of 2-3/8" thick. The finishing materials cannot extend beyond the height of the burner. This burner is designed to be finished with non-combustible materials (ie. tile, granite, marble, brick, etc.) with a minimum thickness of 1/2"... -
Page 22: System Data
installation 886 S.I.T. VALVE PILOT ADJUSTMENT PTO30-NG11 SYSTEM DATA DESCRIPTION Max. Supply Pressure 14" WC (3.49 kPa) Periodically check the pilot flames. Correct flame 1) Manual high/low adjustment Min. Supply Pressure 5" WC (1.25 kPa) pattern has two strong blue flames: 1 flowing 2) Pilot adjustment around the flame sensor and 1 flowing across Manifold Pressure... -
Page 23: Pto60 Assembly
installation PTO60 ASSEMBLY 4. Line the two units up end to end. Screw fireboxes together (one from NOTE: PTO60 is two PTO30 units assembled end to end. each side). You must purchase two PT030s to make a PTO60. 5. Reinstall burner trays. 1 Remove the large stand off on the end of the unit from both PTO30 units - by removing 2 screws per side. -
Page 24: Pto30 Wall Switch And Battery Installation
OUTDOOR SERIES installation WALL SWITCH INSTALLATION PTO30 WALL SWITCH AND BATTERY INSTALLATION (INCLUDED WITH UNIT) (INCLUDED WITH UNIT) The unit comes with low voltage wire and a battery extension wire installed. 6) Install supplied 4-AA batteries into the battery holder. Using velcro install battery holder to the backside of the battery compartment door. -
Page 25: Pto60 Wall Switch And Battery Installation (Included With Unit)
OUTDOOR SERIES installation PTO60 / PTO100 WALL SWITCH INSTALLATION PTO60 WALL SWITCH AND BATTERY INSTALLATION (INCLUDED WITH UNIT) (INCLUDED WITH UNIT) NOTE: PTO60 is two PTO30 units assembled end to end. 6) Attach low voltage wires to the switch - ensure to attach on the right side PTO100 is two PTO50 units assembled end to end. -
Page 26: Pto30/Pt060 Drain Installation (Recommended)
installation PTO30/PT060 DRAIN INSTALLATION (RECOMMENDED) Although this decorative gas appliance is designed to operate outdoors safely, rain and other sources of moisture may enter the burner area, which will cause water to collect inside the base of the unit. NOTE: The PT060 requires installation of 4 drains (two per PT030). To prevent excessive water collection, the installer should provide a way to drain the water from the base of the unit by building or installing a water collector before positioning the decorative gas appliance in its location. -
Page 27: Glass Crystal/Basalt Volcanic Stones Installation
installation GLASS CRYSTAL / BASALT VOLCANIC STONES INSTALLATION Evenly spread the Glass Crystals and optional Basalt Volcanic Stones over the burner. Ensure the crystals (or stones) do not overlap too much as this will effect the flame pattern. IMPORTANT NOTE: Only the supplied approved Glass Crystals and Basalt Volcanic stones are to be used with these fireplaces. -
Page 28: Optional Log Set Installation
PTO30 installation LOG SET INSTALLATION OPTIONAL LOG SET INSTALLATION NOTE: PTO60 requires 2 log sets. Read the instructions below carefully and refer to the images. If the logs are broken do not use the unit until they are replaced. Broken logs can interfere with pilot operation. Improper positioning of the logs may create carbon build-up and can alter the unit's performance which is not covered under warranty. - Page 29 PTO30 installation 4) Install log B on the left side of the burner as shown below. Orient log B in the same way and in a similar position as shown in Diagram 5. Diagram 5 5) Install log F on the burner as shown below. Orient log F across log A in the same way and in a similar position as shown in Diagram 6. Diagram 6 6) Install log C on the left side of the burner as shown below.
-
Page 30: Optional Glass Surround Installation
OUTDOOR SERIES installation OPTIONAL GLASS SURROUND/WINDSHIELD INSTALLATION OPTIONAL GLASS SURROUND INSTALLATION 4 Piece Glass Surround PTO 30-11 PTO60-11 Part N 378-932 Part N 378-955 Overall Dimensions: 37-15/16" long x 16-5/16" wide x 5-5/16" high Overall Dimensions: 68" long x 16-5/16" wide x 5-5/16" high 1. -
Page 31: Assembly Instructions For A Steel Stud See Through Framing Kit For Pto30
installation OUTDOOR BURNER ASSEMBLY INSTRUCTIONS FOR A STEEL STUD ASSEMBLY INSTRUCTIONS FOR A STEEL STUD SEE THROUGH FRAMING KIT FOR PTO30 SEE THROUGH FRAMING KIT Follow these instructions for the 30" burner; **Non-combustible finishing board not supplied with kit. Board may be purchased at your local hardware/building supply store. IMPORTANT: Supplied vents need to be installed into non-combustible finishing board, before applying finishing materials. - Page 32 OUTDOOR BURNER installation 4. Secure all vertical supports (Part B) with two (2) screws each to 1. Attach six (6) short vertical supports (Part C) to base (Part D) with lower frame (Part A). two (2) screws for each support - twelve (12) screws total. Do not install corner screws.
- Page 33 OUTDOOR BURNER installation 10. Install two (2) headers (Part F) with four (4) screws each to complete 8. Secure all tall vertical supports (Part B) to Top and Bottom Frame (Part frame installation A) with three (3) screws each, Diagram 10 & 11 - Part F Diagram 7 Diagram 8 - Screw Locations...
- Page 34 OUTDOOR BURNER installation OPTIONAL PANELS: 1. Bend tabs on top flange of side panel to 90º. Diagram 1 - Bend tabs to 90º 2. Position panel - lower tabs line up with indents in base. Diagram 2 - Lower tabs on panel aligned with base 3.
-
Page 35: Assembly Instructions For A Steel Stud Table Framing Kit For Pto60
OUTDOOR BURNER installation ASSEMBLY INSTRUCTIONS FOR A STEEL STUD ASSEMBLY INSTRUCTIONS FOR A STEEL STUD TABLE FRAMING KIT FOR THE 60" BURNER TABLE FRAMING KIT FOR PTO60 Follow these instructions to construct a steel stud table for the 60" burner; Overall dimensions = 24"... - Page 36 OUTDOOR BURNER installation 3. Install six (6) inner vertical supports - secure each support with two (2) 1. Position each corner vertical support on lower frame and secure with screws to top frame and two (2) screws to bottom frame. four (4) screws each.
-
Page 37: Operating Instructions
operating instructions OPERATING FIRST FIRE INSTRUCTIONS The first fire in your decorative gas appliance is part of the paint curing process. To ensure that the paint 1. Read and understand these instructions before is properly cured, it is recommended that you burn operating this appliance. -
Page 38: Copy Of Lighting Plate Instructions
operating instructions COPY OF LIGHTING PLATE INSTRUCTIONS The lighting plate is located on the underside of the table top on the unit. 38 | Regency Plateau PTO30-11 Outdoor Gas Fireplace ®... -
Page 39: Maintenance Instructions
maintenance MAINTENANCE INSTRUCTIONS 1. Always turn off the gas valve and unplug the batteries before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean paint brush as the logs are fragile and easily damaged. 2. -
Page 40: Valve Assembly Replacement
maintenance VALVE ASSEMBLY REPLACEMENT 10. Remove 8 screws securing valve assembly. Turn the unit off and allow to cool to room temperature. 1. Turn off gas supply 2. Remove the pilot shield. 3. Remove glass crystals, garden stones and log set, if installed. 4. -
Page 41: Gas Maintenance
maintenance Gas Maintenance GAS MAINTENANCE Recommended Annual Routine Maintenance for Gas Fireplaces, Stoves and Inserts In order for your Regency appliance to continue to provide comfort to your home periodic maintenance must be performed to ensure it is operating at peak efficiency. The items in the list should be checked by a licensed gas service technician during the annual service check. Your unit may require more frequent maintenance checks if you notice any changes in how it operates. Operational changes to look for can include, but are not limited to, extended start up time, increased fan noise, residue/carbon build up, white build up on the glass/firebox, increased operating noise etc. Should any of these or other conditions arise, discontinue use and schedule a service check with your local licensed gas technician. The list below shows items your licensed service technician will need to check and service at least annually. Clean Inspect Check • Glass • Pilot assembly • Voltage on thermocouple/thermopile (mil- • Interior bricks / panels • Burner livolt models) • Burner ports & burner air shutter • Pressure relief gaskets/doors • Ohms reading on flame sense (electronic •... -
Page 42: Parts
parts list PARTS Part # Description 377-024 Burner Tray 377-035 Finishing trim 647-519 Pilot Shield 377-027 Burner Mount 377-086 Burner Tray End 377-087 Offset Bracket 376-526 Burner Tube Assembly NG/LP 377-047 Components Cover 911-004 Valve NG 886 SIT IPI On/Off 0.886.002 911-005 Valve LP 886 SIT IPI On/Off 0.886.003 911-276... -
Page 43: Optional Accessories
parts list 932-009 3/8" Stainless Steel Flexible Tubing 904-658 Gas Inlet Line 24 Inches 911-087 Double Gang Front Cover 911-088 Double Gang Box Grey 910-363 Wall Switch 940-532/P Tempered Glass Sides 5" X 14-5/8 " (Each) 940-374/P Tempered Glass Front 5" X 36" (PTO30) (Each) 940-377/P Tempered Glass Front 5"... - Page 44 parts list PARTS NOTE: PTO60 is two PTO30 units assembled end to end. 44 | Regency Plateau PTO30-11 Outdoor Gas Fireplace ®...
- Page 45 notes Regency Plateau PTO30-11 Outdoor Gas Fireplace ®...
-
Page 46: Warranty
warranty Limited Warranty FPI Fireplace Products International Ltd. (for Canadian customers) and Fireplace Products U.S., Inc. (for U.S. customers) (collectively referred to herein as “FPI”) extends this Limited Warranty to the original purchaser of this appliance provided the product remains in the original place of installation. The items covered by this limited warranty and the period of such coverage is set forth in the table below. - Page 47 warranty Replacement units are limited to one per warranty term. Unit must be installed according to all manufacturers’ instructions as per the manual. All Local and National required codes must be met. The installer is responsible to ensure the unit is operating as designed at the time of installation. The original purchaser is responsible for annual maintenance of the unit, as outlined in the owner’s manual.
- Page 48 warranty Limitations of Liability: The original purchaser’s exclusive remedy under this warranty, and FPI’s sole obligation under this warranty, express or implied, in contract or in tort, shall be limited to replacement, repair, or refund, as outlined above. IN NO EVENT WILL FPI BE LIABLE UNDER THIS WARRANTY FOR ANY INCIDENTAL OR CONSEQUENTIAL COMMERCIAL DAMAGES OR DAMAGES TO PROPERTY.
- Page 49 warranty Product Registration and Customer Support: Thank you for choosing a Regency Fireplace. Regency strives to be a world leader in the design, manufacture, and marketing of hearth products. To provide the best support for your product, we request that you complete a product registration form found on our Web Site under Customer Care within ninety (90) days of purchase.
- Page 52 Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ___________________________________________________________________ Installer: ___________________________________________________________ Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial #: ____________________________________________________________ Printed in Canada Regency, Regency Plateau are trademarks of FPI Fireplace Products International Ltd. © Copyright 2021, FPI Fireplace Products International Ltd. All rights reserved.