Download Print this page
Sealey SFE06 Quick Start Manual

Sealey SFE06 Quick Start Manual

6 ltr foam fire extinguisher

Advertisement

Quick Links

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
1. safetY
Do not use for any purpose other than that which the extinguisher is intended for.
8
Extinguishers should remain in their allocated location, and should be used only for the purposes of extinguishing a fire.
9
on no account should the extinguisher be removed for any other purpose, and should not be subjected to any impact, force, heat,
9
abrasion or any other misuse or condition that may be detrimental to the integrity of the extinguisher.
Confirm that the pressure gauge indicator (where applicable) is in the green zone at room temperature.
9
Confirm that the anti-tamper seal holding the safety pin in place is intact.
9
Confirm that the discharge hose, horn or nozzles are firmly attached to the extinguisher.
9
Check that the extinguisher has suffered no physical damage in transit.
9
It is essential that extinguishers are not subjected to temperatures outside of the temperature range stated on the extinguisher.
9
2.
introDuction
i
SFE06 AFFF (aqueous film-forming foam) extinguisher suitable for use on A, B Class fires. Leak-tested and features polypropylene
lined cylinder with brass valve assembly. Five year warranty. Refillable, supplied with wall mounting bracket and pressure gauge. Fully
accredited to BS EN3 and Kite marked.
3.
specification
i
Model no: ................................................................... SFe06
Capacity: ........................................................................... 6ltr
Class/Type: ............................................................. AB/Foam
Fire Test Rating: ..................................................... 13A/144B
Working Pressure:.........................................................12bar
Height/diameter: ................................................. 540/220mm
Weight: ........................................................................ 10.1kg
discharge duration: ..................................................... 38sec
discharge Range: ........................................................3-4mtr
Working Temperature: ......................................... +5 to +60°C
4. installation
4.1.
Fire extinguishers should be commissioned and installed by a Competent Fire engineer who will check the product prior to installation
and apply a service label. Some Insurance Policies may be invalidated if the service label does not carry a Fire engineers signature.
4.1.1.
The names of Fire Engineering companies can be found on-line or in Yellow Pages or similar under such headings as Fire Protection
Engineers and Fire Extinguishing. These Companies will not only install your extinguisher(s) but provide longer term servicing cover.
4.1.2.
We would recommend that a Company approved by FETA, BAFE, BSI or the British Fire Consortium be selected.
4.1.3.
For further advice on the location of your extinguisher please contact your local Fire Engineer or Fire Brigade.
4.1.4.
The extinguisher mounting bracket should be fixed to the wall so that the extinguisher handle is approximately 1 metre above the floor.
4.1.5.
Extinguishers should remain in their allocated location, and should be used only for the purposes of extinguishing a fire.
4.1.6.
on no account should the extinguisher be removed for any other purpose, and should not be subjected to any impact, force,
heat, abrasion or any other misuse or condition that may be detrimental to the integrity of the extinguisher. It is essential that
extinguishers are not subjected to temperatures outside of the temperature range stated on the extinguisher.
4.1.7.
Fire extinguishers are life saving appliances and as such, need to operate correctly in the event of a fire.
Do not use as a toy.
© Jack Sealey limited
6 ltr foam fire extinguisher
sfe06
Model no:
Original Language Version
SFE06 Issue 2 (H, 4, 5, F) 12/11/18

Advertisement

loading

Subscribe to Our Youtube Channel

Summary of Contents for Sealey SFE06

  • Page 1 Model no: thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. important: no liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey group, Kempson Way, suffolk Business park, Bury st edmunds, suffolk. ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk...