Page 1
OWNER’S MANUAL TYPE EN27-- TYPE EN37-- WARNING FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this manual, this product must be serviced by a pool technician who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist.
Page 2
ROBOTIC CLEANER FCC STATEMENT This device complies with Part 15 of the FCC Rules and IC licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
OWNER'S MANUAL TABLE OF CONTENTS Important Safety Instructions ...... 4 Cleaner specifications ........5 Technical Specifications ..............5 Getting Started ..........6 Contents .................... 6 Connect to a Power Source ............6 General Cleaner information ......7 Install and Submerge the Cleaner ..........7 Control Box Buttons...............
ROBOTIC CLEANER SECTION 1. IMPORTANT SAFETY INSTRUCTIONS Please read through the entire manual before installing your new robotic pool cleaner. The cleaner must be installed and operated as specified. WARNING Failure to comply with the following warnings can result in permanent injury, electrocution or death.
OWNER'S MANUAL CAUTION Failure to comply with the following warnings could cause damage to pool equipment or personal injury. • The cleaner must be installed and operated as specified. • This product is intended for use with permanently-installed pools. Do not use with storable pools. A permanently- installed pool is constructed in or on the ground or in a building such that it cannot be readily disassembled for storage.
ROBOTIC CLEANER SECTION 3. GETTING STARTED • Firmly insert power cord connector (with TOP shown facing up) until you hear a "click" CONTENTS (Figure 1). The packaging should contain the following items: NOTE: The "click" indicates the power cord is connected correctly.
OWNER'S MANUAL INSTALL AND SUBMERGE THE SECTION 4. GENERAL CLEANER CLEANER With the control box plugged into a power INFORMATION outlet, spread the fl oating cable across the pool deck until you reach the middle of the pool CAUTION length. WARNING: Do not use an extension cord To prevent damage to the cleaner, to adhere to the following guidelines:...
ROBOTIC CLEANER START / STOP CLEANING AND Place all of the fl oating cable in the water to SELECT CLEANING MODE allow free movement in your pool from the central point. Spread out the fl oating cable The factory default cleaning mode is set to Floor, Wall, ensuring there are no kinks or coils in the Waterline.
OWNER'S MANUAL NOTE: Never lift the cleaner out of the pool by the floating SECTION 5. MAINTENANCE cable. WARNING To avoid electric shock and other hazards which could result in permanent injury or death, disconnect (unplug) the cleaner from the power source before performing any cleaning and maintenance.
ROBOTIC CLEANER CLEAN THE FILTER CANISTER Hold the cleaner vertically to drain (Figure 8). The fi lter canister should be cleaned after each cycle. Remove the cleaner from the water and let the remaining water drain. Unlatch the cleaner cover to access the canister (Figure 11).
OWNER'S MANUAL STORE THE CLEANER WHEN REPLACING BRUSHES NOT IN USE The cleaner is fi tted with brushes with a ''wear'' The cleaner should be cleaned regularly using indicator (Figure 15). slightly soapy water. Do not use solvents such as trichlorethylene or its equivalent.
Page 12
ROBOTIC CLEANER Figure 17. Undo the Tabs of the Brush Figure 20. Cut Tabs Position the new brush underneath the roller with the bristles facing downwards (see Figure 18). Figure 18. Position the New Brush on Roller Thread each tab into the slot provided and gently feed it through until the heel comes out at the other side of the slot.(Figure 19).
OWNER'S MANUAL SECTION 6. TROUBLESHOOTING If the status indicator on the control box fl ashes, follow the recommended troubleshooting tips below. ERROR CODES Solutions Flashing LED • Disconnect and reconnect the cleaner. • Check that the cable is properly connected to the control box.
ROBOTIC CLEANER GENERAL TROUBLESHOOTING The following list provides some helpful hints for troubleshooting common challenges when using the cleaner. User Issue Possible Cause Suggested Solution The cleaner does not stay There is air trapped inside the Remove cleaner from pool and re-submerge on the pool surface or is cleaner housing.
Page 16
Jacuzzi Inc. All other brands, product names, company names, trade names ® and trademarks used are the property of their respective owners. Jacuzzi may add to change or remove any part of these materials at any time, without notice. Reproduction in whole or inpart without written permission is prohibited.
Need help?
Do you have a question about the EN27 Series and is the answer not in the manual?
Questions and answers