Summary of Contents for Tekvox TPHD2-WP1
- Page 1 TPHD2-WP1 79066 User Manual TPHD2-WP1 HDMI/VGA Wall Plate Switcher & HDBaseT Lite Transmitter 2-gang, Decora-style All Rights Reserved Version: 79066_2020V1.0 www.tekvox.com...
- Page 2 TPHD2-WP1 79066 User Manual Preface Read this user manual carefully before using the product. Pictures shown in this manual are for reference only. Different product model specifications may vary. This manual is only for operation instruction, please contact the local distributor for maintenance assistance.
- Page 3 TPHD2-WP1 79066 User Manual Safety Precautions To ensure the best performance from the product, please read all instructions carefully before using the device. Save this manual for further reference. • Unpack the equipment carefully, and save the original box and packing material for possible future shipment •...
-
Page 4: Table Of Contents
TPHD2-WP1 79066 User Manual Table of Contents 1. Product Introduction ........................5 1.1 Features ............................... 5 1.2 Panel Descriptions ..........................6 1.2.1 Front Panel Description ......................6 1.2.2 Side Panel Description ....................... 7 1.2.3 Rear Panel Description ......................7 2. Application ........................... 8 3. -
Page 5: Product Introduction
A long with the ability to provide HDMI and VGA source connections, the TPHD2 WP1 is designed to support the TEKVOX TekTouchPad with power and RS232 on its back side for easy integration. Special RS232 commands are utilized to improve communication between the TekTouchPad and TekMonitor. -
Page 6: Panel Descriptions
Press and hold for 3+ seconds to enter Manual-Switching Mode Serial port 3-pin pluggable terminal block. Used to setup and control the RS232 Port TPHD2-WP1 or send bi-directional RS232 data to remote device. Connect a VGA source device. The indicator lights up yellow when there VGA In is a VGA signal present, and lights up green when the input is selected. -
Page 7: Side Panel Description
Connect to DC 12V power adapter if not being powered by receiver Power Out Supplies DC 12V power for TekTouchPad (if used) Bi-directional RS232 port for connection to TekTouchPad. This port can RS232 be used to control the TPHD2-WP1, or to control a remote device connected to the receiver. www.tekvox.com... -
Page 8: Application
79066 User Manual 2. Application By using the TPHD2-WP1 wall plate with a TekTouchPad and networked controller, a simple controlled audiovisual system can be implemented. The RS232 and power connections on the rear of the wall plate make it easy to connect to a TekTouchPad. When using a controller such as a TEK 3, the TekTouchPad is programmed only to communicate with the TEK 3 and not the display. -
Page 9: Operation
RS232 port. Both automatic and manual switching between HDMI & VGA are supported. By default, the TPHD2-WP1 is set to auto-switching, and the button is illuminated. To set the unit to manual switching, press and hold the Source/Auto button for 3 seconds or more or send the RS232 command “40771%”. -
Page 10: Rs232 Commands
TPHD2-WP1 79066 User Manual 3.2.3 RS232 Commands Communication Protocol: RS232 Communication Protocol Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: None Note: • Commands with a gray background are for VGA sources ONLY • EDID commands are for HDMI sources ONLY 3.2.3.1 Switch Commands... - Page 11 TPHD2-WP1 79066 User Manual Command Function Feedback Example 40628% Change the resolution to 1280x800 (WXGA) Resolution: 1280x800 40629% Change the resolution to 1920x1080 (1080P) Resolution: 1920x1080 40620% Change the resolution to 1920x1200 (WUXGA) Resolution: 1920x1200 46021% Change the resolution to 1600x1200 (UXGA) Resolution: 1600x1200 3.2.3.3 Setup Commands...
- Page 12 TPHD2-WP1 79066 User Manual Command Function Feedback Example 40633% Check the picture mode Picture Mode: xx 40793% Check HDCP Status HDCP Off/On/Active 40635% Check the image aspect ratio Aspect Ratio: xx 40636% Check the brightness Brightness: xx 40637% Check the contrast...
- Page 13 TPHD2-WP1 79066 User Manual Command Function Feedback Example 40777% Set EDID data to 4K*2K PCM 2.0ch EDID:4K&PCM 2ch EDID:1080P&PCM 2ch EDID:1080P&5.1ch 40778% Check EDID data EDID:1080P3d&5.1ch EDID:4K&PCM 2ch 40799% Program EDID file, send EDID data within 10s Waiting for EDID within 10 secs!
-
Page 14: Device Specifications
TPHD2-WP1 79066 User Manual 4. Device Specifications Model TPHD2-WP1 (79066) 1 HDMI (19-pin HDMI, female) 1 VGA (15-pin VGA, female) Input 1 AUDIO (3.5mm mini jack) 1 RS232, Front (3-pin Phoenix) 1 RS232 and Power In/Out, Rear (6-pin Phoenix) Output... -
Page 15: Troubleshooting & Maintenance
TPHD2-WP1 79066 User Manual 6. Troubleshooting & Maintenance Problems Causes Solutions Check connections and cable. Loss of video or noise CAT cable or RJ45 connector issues. Best to use CAT 6 shielded. on the screen Distance may be too long.
Need help?
Do you have a question about the TPHD2-WP1 and is the answer not in the manual?
Questions and answers