Advertisement

Congratulations for choosing VULCAN
tric heating system. It is loaded with 37,000
BTU's of heat power, offers wide range of air
flows and precise temperature controls. It
features individually controlled heating elements,
variable
speed
blower
temperature controller. 25' thermocouple probe
can measure containment air or material
temperature for efficient and safe heat control.
The intended use of the Vulcan is temporary heat
for construction sites and restoration projects to
shorten structural drying.
Vulcan delivers the heat safely and
efficiently where you need it... When
you need it...
CAUTION
Caution – High temperature, keep electrical cords, drapery
and other furnishings at least 3 Ft (0.9 m) from the exhaust of
the heater and from the side and rear.
Attention - haute température, garder les cordons
électriques, les draps(couvertures) et d'autres fournitures à
au moins 3 pi (0,9 m) de l'échappement de l'appareil de
chauffage sur le côté et en arrière.
This equipment to be operated only by trained personnel.
Do not use with combustible or explosive material.
Do not expose to water or rain.
Connect only to grounded outlet with GFCI device.
Disconnect power for cleaning and servicing.
Cet équipement à être exploité uniquement par du personnel qualifié.
N'utilisez pas avec des matériaux inflammables ou explosifs.
N'exposez pas à l'eau ou à la pluie.
Se connecter uniquement à la sortie avec dispositif de GFCI.
Coupez l'alimentation pour le nettoyage et l'entretien.
elec-
and
programmable
WARNING
Vulcan Heater
CAUTION
RISK OF ELECTRIC SHOCK
NO USER-SERVICEABLE PARTS INSIDE
Risque d'électrocution
Aucune pièce utilisable à l'intérieur
1
CAUTION
DO NOT OPEN
Prudence
Ne pas ouvrir

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VULCAN and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnitec VULCAN

  • Page 1 25’ thermocouple probe can measure containment air or material temperature for efficient and safe heat control. The intended use of the Vulcan is temporary heat for construction sites and restoration projects to shorten structural drying. Vulcan delivers the heat safely and efficiently where you need it...
  • Page 2 Do NOT operate the Vulcan without air filter. Do not insert or allow foreign objects to enter intake or outlet openings as this may cause electrical shock or fire or damage heater. Heater will be hot during operation, use handles when moving.
  • Page 3: Table Of Contents

    SPECIFICATIONS Table of Contents Introduction ........... 1 MODEL: OVH-230 Safety Instructions ........ 2 Power Supply: 230VAC/60Hz/1 phase Specifications ........3 50 amp supply - can operate all 6 heating ele- ments, 50 amp load, 37,000 BTU output Parts List ..........4 30 amp supply - can operate up to 3 heating Operations Overview ......
  • Page 4: Introduction

    Vulcan Operation Overview Flexible Duct, 10”x25’ ......OAD10 Thermocouple K , 25 ft ………………………..RTS12 Vulcan delivers up to 37,000 BTU and 400 cfm of air Options: flow at temperatures from ambient to 160° F. The Range Adapter 15’ 125/250/50 amp ..EDP50/1 heater outlet can be ducted to deliver heat where need- Dryer Adapter 15’...
  • Page 5 150° F. from power supply. Electrical Requirements: Vulcan unit requires Temperature controller: figure 1, #3 230VAC/ 1 Phase power source with over-current pro- tection rated at 50 amp maximum. It can be dryer/range...
  • Page 6: Controls

    Change your SP as needed at any time. Operation: After the heater stabilizes at your required temperature, 1. Inspect Vulcan and the power cord for any damag- check the operation of the heating elements. If the es before using. Do not use the system or the cords Temperature Controller is frequently turning the heat- if damaged.
  • Page 7: Maintenance

    This guide may identify easy to correct problems in Faulty heater switch or heating element Vulcan operation and does not require opening the unit. Only qualified maintenance person should replace inter- Problem — Heater is frequently cycling ON and OFF nal heater parts.
  • Page 10: Warranty

    WA 98275; www.omnitecdesign.com In order to keep this in effect, the purchaser must (i) return this signed LIMITED WARRANTY to Omnitec Design within 30 days of purchase date, (ii) have promptly informed Omnitec Design’s Customer Service of any defects and (iii) properly used and maintained the Product.

Table of Contents