Moog N123-134 Series Setup

Moog N123-134 Series Setup

Exciter/demodulator

Advertisement

Quick Links

SPECIFICATIONS

Input
Differential input across terminals
10 and 11.
AC input signal level should
be from .07 to 7.0 Vrms for
±10 VDC output.
Input impedance can be assumed
to be 40KΩ (with standard
values of R30, R31, R32, and R33).
Outputs
Excitation Output:
Frequency varies with C3, C4,
and R3.
As shipped: Freq. varies
100 to 2,000 Hz
Remove C3—Freq. varies 500
to 10,000 Hz
Amplitude—2 to 11 V p-p
Stability—amplitude varies
≤ 250 ppm/°C
N123-134 Exciter/Demodulator:This Snap Trac module contains a power
oscillator and a demodulator for use with LVDT's, synchros and other carrier
excited, amplitude modulated, transducers. Carrier frequencies can be set
from 100 to 10,000 Hz.
SPECIFICATIONS
Demodulator Gain: General
expression for gain of the DC voltage
at terminal 12 assuming R33=R32,
R31=R30 and R34 fully CW
(i.e. max span setting)
R
R
R
32
37
45
e
=1.41*
*1+
*
(e
-e
) VDC
12
11
10
R
R
R
30
38
39
where e
and e
are Vrms
10
11
Differential Amplifier Gain:
R
(e
-e
)
Vout =
( )
32
10
11
R
30

FEATURES

Construction
Plug-in connectors for quick installation of board.
Test points on all critical signals for easy system setup.
Component standoffs on all user-configurable components.
Twenty-turn potentiometers for all adjustable controls.
Rugged construction with solder mask for reliability.
Demodulator Output:
to ±10 VDC nominal at Terminal 12
Ripple: < 40 mV p-p at
≥ carrier freq.
Linearity: ≤ ±0.2% at 1.2 kHz
Stability: ≤ 250 ppm gain/°C
±0.1 mV/°C
Polarity: Output at terminal
12 is negative when voltage at
terminal 11 is in phase with
terminal 3
Load Impedance: > 5KΩ
Frequency Response: Phase lag of
demodulator output signal increases
linearly from 0˚ to 180˚ as frequency
of modulation increases from zero to
the carrier frequency.
Temperature Range:
-20˚C to 50˚C (-4˚F to 122˚F)
Power Required:
±E: ±15 VDC reg, 3-wire @ ±50 mA
at pin-6, 7 & 8
±V: ±15 VDC to ±22 VDC unreg @
±40 mA, 3-wire at pin-1, 2 & 9
(or 7)
This power is available from the
Model N121-132A Snap Trac
Servocontroller.
N123-134 Series
Exciter/Demodulator
Q2
R26
D2
D3
U3
R24
R23
C6
R27
R22
D4
D5
R11
R28
R6
C8
C10
R20
R29
R7
R3
R33
D6
R34
D7
R31
U4
R30
R44
C11
R45
U6
R41
R40
R42
MODEL:N123-134
SN:

MOUNTING HARDWARE

PVC Snap Trac, Part Number 65419-1

DIMENSIONS

Exciter/Demodulator: 3.25 in x 6.00 in long
Maximum Component Height: 2.42 in
Q1
R25
R18
D1
R17
R19
R10
U2
R9
R13
R16
R12
R14
R5
R15
R21
R8
U1
R2
R1
R4
C4
R35
C3
R32
C16
R37
C17
R38
R36
R39
U5
R43
C13
C12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the N123-134 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Moog N123-134 Series

  • Page 1 SPECIFICATIONS N123-134 Series Input Demodulator Output: Exciter/Demodulator Differential input across terminals to ±10 VDC nominal at Terminal 12 10 and 11. Ripple: < 40 mV p-p at ≥ carrier freq. AC input signal level should Linearity: ≤ ±0.2% at 1.2 kHz be from .07 to 7.0 Vrms for...
  • Page 2 N123-134 EXCITER/DEMODULATOR SCHEMATIC 0.01µF 0.0022µF WAVEFORM GENERATOR 0.01µF 33pF 49.9K TIP29C 8038 LM301AN 49.9K DEMODULATOR PHASE 1N4148 100K 49.9K 1µF,63V OSCILLATOR LEAD OSCILLATOR AMPLITUDE 100K 2 1 R10 FREQUENCY 12.1K 12.1K 22.1K 0.33µF,63V 1N4148 1N4148 15pF 4.99M 18.2K 2N2222A TIP30C 49.9 100K 1.5K...
  • Page 3 TEST SET -UP PROCEDURES 333 Acqs Verify ±15 VDC at Pins 6 & 8. 12. The DEMODULATOR PHASE Tek Stop: 2.50MS/s All voltage measurements are pot (R11) adjusts timing of with respect to Pin-7 or TP7 (PC trigger pulse for peak sampling of Ch 1 Freq Board Analog Common).
  • Page 4 SNAP TRAC EXAMPLE Suggested Setup Procedure: (Reference Moog Documents N121-132A and N123-134) Turn off hydraulic power and relieve pressure. Set the GAIN pots (R4 and R43) on the N121-132A card approximately five turns from full counter-clockwise. Set the SCALE pot (R9) on the N121-132A card full clockwise.

Table of Contents