Sealey LEDSTR03 Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Indoor use only
instructions
1. SAFETY
1.1. GENERAL
DO NOT shine directly into your, another person's or an animal's eyes.
8
DO NOT allow children to use the strip light.
8
DO NOT use the strip light if you suspect that the battery case or any part of the strip light is damaged.
8
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using this
‰
light.
Inspect the cable and connector for wear and damage to ensure items are safe before connecting to the power supply. If worn or
9
damaged DO NOT use.
IMPORTANT: Check that the voltage marked on the charger plug is the same as the lamp when using your own plug adapter.
Uncoil the cable between charger and the lamp.
9
DO NOT use a USB cable or Plug adapter that exceeds 5V-2A, doing so will damage the product and void any warranty.
8
DO NOT pull the charger plug from the mains socket by the lead.
8
DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).
8
1.2. BATTERY SAFETY
WARNING! To reduce the risk of burns or fire:
‰
DO NOT attempt to open, disassemble, modify or service the battery case.
8
DO NOT leave batteries in supplied battery case for long periods of inactivity.
8
DO NOT crush, puncture, short external contacts or dispose of in fire or water.
8
DO NOT expose to temperatures above 60°C (140°F).
8
Replace only with the batteries designated for this product.
9
Recycle or dispose of used batteries as stipulated by local regulation.
9
If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool
9
water and seek immediate medical attention.
2. INTRODUCTION
Linkable LED strip lights with PIR and CDS sensor. The sensor only works in dark (illuminance ≤10-20 LUX). The PIR and CDS sensor can be
set to two modes, 30 seconds and 1 minute before turning off. This allows you to leave the light on when not in use and it will turn off after the
set period when no movement is detected. Each strip features 6 SMD LED's and can be linked to up to 5 strips. Each pack includes 2 corner
extensions, one cover for the end of the strip and 6 metal clips with option of using the included screws or adhesive strips to attach to almost
any surface. USB powered and can be used with the battery case supplied (4 x AAA batteries not included) which can also be mounted using
the bracket supplied, any 5V-1A/2A power bank or a 5V-1A/2A USB plug adaptor.
3. SPECIFICATION
MODEL NO: ....................................................... LEDSTR03
Battery: ............................................... 4 x AAA (not included)
LED Qty: ............................................................... 3 x 6 SMD
Length: ............... 306 x 8.44 x 6.80 mm (L x W x D) Per Strip
Lumen Output: ............................................................. 150lm
Operating Time: .............................................................. 4hrs
4. OPERATION
4.1. SETTING UP
4.1.1. Connect the light tubes together by removing the end caps and slotting the tubes into each other.
4.1.2. Use the elbow pieces if you need to go around a corner or get the light further back into the cupboard.
4.1.3. Attach the metal clips to the light and stick the adhesive pads to the clips.
4.1.4. Place in desired location.
4.2. USE WITH SUPPLIED BATTERY UNIT
4.2.1. Insert the batteries into the battery unit, and plug in using micro usb.
© Jack Sealey Limited
3PC LED STRIP LIGHTING
LEDSTR03
MODEL NO:
Original Language Version LEDSTR03 Issue 1 09/09/2020