Table of Contents
Advertisement
Quick Links
Before using this product, carefully read this instruction manual for proper use.
Keep this instruction manual in a safe place.
If you are to give this product to a third person, provide him/her with this manual as well
to ensure safe use.
IF44
Failure to follow this warning can result in serious accidents including death or serious injury.
Warning
●This product is made specifically for fishing rods and those with reels attached.
Do not use for other purposes.
●Do not modify this product.
●Avoid overspeeding, sudden starts, sudden turns, and sudden braking as much as possible.
●Close the cover securely and lock with the key. Failing to do so may cause the cover to open while
driving, and the rod box to be damaged and/or to fall off the vehicle roof due to wind pressure.
●Before driving, check the two installation positions with the base carriers, and the bolted positions on
the product body are securely tightened. Re-tighten all loosely-bolted positions.
Failure to follow precautions can result in injury, damage to the product, vehicle, or load.
Precautions
●Make sure that the vehicle rear hatch (trunk) does not hit the rod box when opening.
●The rod box is not constructed to be completely waterproof.
Loaded items may get wet due to strong rain.
●Opening and closing the rod box during strong gusts or winds may cause the box to be damaged,
or have your body trapped in the box, leading to injury.
●Always remember that the vehicle height has increased when the rack is installed.
●Remove the rack before using an automatic car wash.
●Do not use a car cover (including a cover for preventing paint splatter) with this product installed.
The rod box may deform due to weather conditions such as high temperatures.
●Do not place any items on this product. Doing so may cause cover deformation.
Before using this product, the followings should be noted.
Note
●The rod box materials gradually deteriorate due to exposure to UV light. If you do not plan to use the rod
box for a long period of time, store it away from direct sunlight, high temperature, and high humidity.
IF44 Rod Box Installation Instructions
−1−
5590627A
Advertisement
Table of Contents
Summary of Contents for INNO IF44
- Page 1 5590627A IF44 Rod Box Installation Instructions Before using this product, carefully read this instruction manual for proper use. Keep this instruction manual in a safe place. If you are to give this product to a third person, provide him/her with this manual as well to ensure safe use.
-
Page 2: Product Contents
Product contents Common parts Part name Body A (Cover A & Bottom A hinged) Body B (Cover B & Bottom B hinged) Body C (Cover C & Bottom C hinged) Frame Memory mount Bottom plate Hexagonal concave bolt *1 Knob nut Joint bolt Joint nut Knob bolt... - Page 3 Determining a Length The length of this product can be adjusted at three levels according to your longest rod. Loadable rod length Short position 2,200 mm (7’ 2” ) Short position Medium position 2,480 mm (8’ 1” ) Long position 2,760 mm (9’...
- Page 4 Loose bolting Hex Wrench Cover Cover B Body B Frame Bottom B Hexagonal concave bolt Open Cover B. Align the nut on the frame edge with the hole on Bottom B that is proximate to the center. Loosely bolt all of four nut portions with the hexagonal concave bolt. Note As Body B is not equipped with a damper between Cover B and Bottom B, Cover B goes freely as far back as to the other side.
- Page 5 Hexagonal concave bolt Specification sticker in your language Attach the four frames to Bottom A and C by firmly bolting the hexagonal concave bolts in all the 12 locations, holding the longer end of the hex wrench to tighten.(4Nm) Stick the specification sticker described in your language. Joint bolt Knob nut Knob bolt...
- Page 6 Deciding the installation position of the Rod Box Confirm that the base rack is correctly installed, and temporarily place the rod box on the base rack. Open Cover A, B and C. Adjust the position of the product so that the slits are placed on Distance between the base racks the base rack.
- Page 7 *Cannot be installed onto round bars. This rod box is mountable onto genuine base racks and crossbars of the vehicle manufacturer, as well as the INNO crossbars. Make sure to install the base rack and/or crossbars securely. Warning Check vehicle or base rack product instructions to confirm that the base rack to which this product is to be installed has sufficient strength to support this product.
- Page 8 Precautions If the height of the 2 hooks differs, the hook center will not match the base bar center. Check that hooks are symmetrically positioned. The hooks may loosen over time if they are not symmetrically positioned. Readjust the adjuster knob to tighten. Note When the square bar is placed, keep the tips of the hooks as close as illustrated.
- Page 9 Loading rods Loadable rod length Short position 2,200 mm (7’ 2” ) Medium position 2,480 mm (8’ 1” ) Short position 2,760 mm (9’ 0” ) Long position Medium position Long position Bottom cushion Grip cushion Temporarily place the grip cushions and the bottom cushions as illustrated. Place your rods with their reels attached.
-
Page 10: Maximum Load Capacity
When placing multiple rods, alternate the direction of each rod's grip / tip. Precautions Ensure the tip of the rod does not stick out of the body, or it does not hit the damper. Damper Body A or C Note Note If you have difficulty opening the cover, lift the two portions on the center simultaneously shoulder-width apart. - Page 11 Checking before driving Shake the rod box in all directions, right and left, backward and forward, and up and down, to look for any rattling caused by improper installation. If you still hear or feel rattling, go back to Section 4 "Installation of the Rod Box"...
-
Page 12: Repair Parts
Repair parts Repair parts Part name ISP1130 Frame ISP1109 Memory mount * ISP1131 Bottom plate Hexagonal concave bolt ISP833 (Set of installation bolts) ISP1132 Knob bolt ISP1133 Joint bolt ISP1134 Joint nut ISP1135 Knob nut ISP1136 Filler cap ISP1137 Grip cushion ISP1138 Bottom cushion ISP270...
Need help?
Do you have a question about the IF44 and is the answer not in the manual?
Questions and answers