Advertisement
Quick Links
These instructions are intended for the following part numbers:
Vehicle Fitment:
2017-2019 Audi RS3 Sedan 2.5L Turbo
•
2017-2019 Audi TTRS Coupe 2.5L Turbo
•
Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0
2660-15050
Thank you for purchasing the
Carbon Intake System
Exquisite build quality with industry leading
performance
distinguish this intake kit from all others.
AWE 4.5" S-FLO Closed
for RS3 and TTRS.
Installation questions?
CONTACT US
Advertisement
Summary of Contents for AWE S-FLO
- Page 1 Exquisite build quality with industry leading performance distinguish this intake kit from all others. Installation questions? CONTACT US Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 2 94500A231 100-120 worm drive clamp 5574K25 #10 washer 96659A104 M4x12x0.7 bolt 91292A117 M5 flat washer 93475A240 Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 3 Figure 2-2. Note: These screws will not be reused with the AWE carbon inlet duct. Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 4 Loosen the 2 hose clamps holding the OEM intake hose in place, shown in Figure 4-1. Then carefully remove the intake hose from the intake, shown in Figure 4-2. Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 5 Figure 6-1. Next squeeze the hose clamp and pull the intake tube off of the turbo inlet, shown in Figure 6-2. Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 6 2 supplied 100-120 worm drive clamp, as shown in Figure 9. Note: Do not tight hose clamps at this point. Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 7 Install the AWE air filter onto the AWE intake tube and tighten the 110-130 worm drive clamp hose clamp, as shown in Figure 12. Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 8 Figure 15. Careful not to over tighten hardware, as carbon could crack. Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 9 Reinstall the OEM engine cover by pressing it back into place, as shown in Figure 18. Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
- Page 10 215-658-1670 CONTACT FORM Up-to-date warranty information is found HERE. Copyright 2019, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. All rights reserved. Rev1.0...
Need help?
Do you have a question about the S-FLO and is the answer not in the manual?
Questions and answers