USAutomatic 050500 Manual

WIRELESS KEYPAD
06 8 1
Part # 050500
Made in Italy
Part # 050520
Thank you for choosing this product.
Please read this manual carefully before using the product.
1 - Introduction
The Wireless Keypad ( PN 050550 ) is an encoded radio keypad
operating at 433,92 MHz.The best use of the product is on applications
where an encrypted radio signal has to be used to control: gates, garage
doors, rolling shutters, sun-blinds, anti-burglar appliances, lightings,
etc. The code has a very high security coding system (19683 code
combinations). The radio transmission is enabled only after the dialing of a
security user code. There are up to 4+2 different channels that can
activate up to 6 different receivers or relays.
The internal memory can store up to 24 different security user codes and
1 Master code.
The product fully complies with the European directives 89/336/CEE,
99/05/CE and Part. 15 of FCC Rules..
2 - Technical specifications
Number of keys: ...................................................................................12
Number of channels:.........................................................................4 + 2
Supply: ............................................................................................3 Vdc
Battery duration: ............................................................about 36 months
Battery type: .................................................................Lithium CR123A
Current consumption:.....................................................................20 mA
Operating frequency: ...........................................................433.92 MHz
Modulation: ..............................................................................AM/ASK
E.r.p................................................................................................6 mW
Security Code combinations number: ............................................19683
User security code number:..............................................................24+1
Transmission duration: ................................................until press / 1 sec.
Range in open space: .................................................from 150 to 700 m
Operating temperature: ..........................................
Dimensions: .............................................................
... Weight:.........................................................................................
IP Protection Grade: .........................................................................IP44
PN 050500 / 050520 : Fixed code Radio keyboard without tamper;
Remove the cover and extract the old battery from the bottom site of the
electronic card with an upward traction. Insert the new battery on the
battery location, respecting the right polarity.
LITHIUM CR123A
-
-
Fig. 1
1. Locate the best position for the installation, avoid metallic surfaces
that could decrease the RF emission.
2. Mark the location of the mounting holes using the base as a drilling
template.
3. Drill the mounting holes and insert the plugs.
4. Remove the protection strip from the seal.
5. Assemble the base and seal together.
6. Install the base with the screws supplied.
7. Complete steps 8 and 9.
8. Install the keypad to the base.
9. Secure in place with the 2 screws supplied.
Terms to understand
Master Password: The 5-digit code used to access programming
features. Factory default is "11111." This needs to be changed by the end
user for security reasons.
Access Code: The 1 to 5-digit code used to open the gate (24 unique
codes are possible). If access code is less than 5 digits it requires the #
from 14 °F to 131 °F
sign after code is entered. Example: "2 #." If the code is 5 digits the #
5.7 x 3.07 x 1.25 in
sign is not required.
3.24 oz
Relay 1: The receiver has 2 relays. P1 (relay 1) is factory wired to the
receiver input on the control board.
3 - Types
4 - Battery replacement
NOTES: The appliance uses
a lithium battery type CR123A-
S-3V. The removal and the
disposal of the battery must have
effected before the elimination of
the appliance and a c c o r d i n g t o
t h e c u r r e n t Regulations.
+
ATTENTION: - Danger of
explosion if the battery is not
+
replaced in the correct way!
Replace only with an equal or
equivalent type.
433KPD
FCC ID : PWJDK433
This device complies with FCC Rules Part 15
Operation is subject to the following two
conditions:
1) This device may not cause harmful interferences;
2) this device must accept interference that may
cause undesired operation.
5 - Installation steps
6 - Programming wireless keypad
Relay 2: The receiver has 2 relays. P2 (relay 2) is factory wired to
"Open / Free Exit" input on the control board.
Security Code (Dip Switch Code): The keypad does not have
dip-switches. Instead, the receiver has a learn mode which can be
used to program the keypad to the receiver. The keypad can also be
manually programmed if a transmitter is being used.
See "Changing Security Code" on paragraph 10.
PUK Code: "Password Unblocking Key." The PUK code is
located inside the keypad and is needed when the master password
has been lost. Copy and store in a safe place for future reference.
Must be 5 digits long lead with zeros.
" * " Key: located on the keypad is used to cancel last command
entered.
Red Light Blinks: When blinking, the keypad is sending a signal
to the receiver.
Valid access code was entered.
7 - Master Password
The keypad has a Master Password factory-set to "11111". If the
Master Password remains the default one, the following functions
are allowed:
Insertion of new User Codes;
Cancellation of stored User Codes;
Replacement of the Master key itself.
The Master Password and the User code can have up to 5 digits. If
the chosen code is shorter than 5 digits, press the key "#" after the
last digit, to complete the number, as indicated below:
Example 1 : User code 123 : Enter: 1,2,3,B.
Example 2 : User code 1234 : Enter:1,2,3,4,B. Note:
Do not install keypad until "Create Communication with
Receiver" has been completed (step 9).
8 - Keypad Programming
Create Access Code: (Code you use to operate the gate)
*CAN NOT BE THE SAME AS MASTER PASSWORD!
1. Enter the Master Password "11111". (this is the factory
default master password).
2. Enter "9" If correct, 2 short beeps (if 1 long beep is heard,
start over with step 1).
3. Enter the new Access Code (up to 5 digits), if less than 5
digits, "#" key is required.
4. Enter "9"
5. Enter the new Access Code again to verify.
6. Enter "1". If this access code is for P1 (relay 1) Enter "2" if
this access code is for P2 (relay 2). See Note below.
7. If correct, 2 short beeps (if 1 long beep is heard, start over
8. Continue with "Create Communication with Receiver" to
complete programming.