Table of Contents
Advertisement
Quick Links
Technical Manual
pH regulation and
ORP analysis
for salt electrolysis
Technical Manual
V2.0
Code
Version
MPNT0108
V2.0
CONTENTS
TECHNICAL CHARACTERISTICS .................................................... 2
OVERVIEW ....................................................................................... 3
pH ........................................................................................... 3
Redox ..................................................................................... 3
OPERATION ..................................................................................... 4
Display.................................................................................... 4
pH Menu ................................................................................ 6
Oxidant Menu ...................................................................... 8
Settings Menu ....................................................................... 9
HYDRAULIC CONNECTION ........................................................... 10
Installing the sensors ............................................................ 10
Installing the injector ........................................................... 10
Installation diagram ............................................................ 11
ELECTRICAL CONNECTION .......................................................... 12
SENSOR MAINTENANCE ................................................................ 15
Caution: Please read these instructions carefully before installing, commissioning or
using this appliance
CCEI
PHENIX
Date
03/08/2015
v2.0
page 1
Advertisement
Table of Contents
Summary of Contents for ccei PHENIX
-
Page 1: Table Of Contents
Technical Manual v2.0 PHENIX pH regulation and ORP analysis for salt electrolysis Technical Manual V2.0 Code Version Date MPNT0108 V2.0 03/08/2015 CONTENTS TECHNICAL CHARACTERISTICS ............ 2 OVERVIEW ..................3 pH ................... 3 Redox ..................3 OPERATION ..................4 Display..................4 pH Menu ................ -
Page 2: Technical Characteristics
Technical Manual v2.0 PHENIX TECHNICAL CHARACTERISTICS General Dimensions (l x h x d) in 300x150x90 mm Weight 2 kg Power supply 230V / 50Hz Protection Index IP-55 Class II pH-meter Measurement range 3.9 to 9.9 Measuring resolution +/- 0.1 Sensor... -
Page 3: Overview
The user can configure the PHENIX in pH- mode or in pH+ mode. In pH- mode, the PHENIX injects PHminus (acid) to lower the pH in the pool and in pH+ mode it injects PHplus (base) to increase the pH. PHENIX, specifically designed for swimming pool water, regulates the pH between 6.0 and 8.5. -
Page 4: Operation
The system is switched on using the switch on the front of the device. PHENIX has a drop-down menu so you can see the status of the different PHENIX variables. In addition, this drop-down menu allows you to access the “SETTINGS”... - Page 5 The result is expressed in ppm, equivalent to mg/l. This values is calculated according to the parameters measured by the PHENIX and a theoretical formula combining pH, ORP and temperature but is provided merely as an indication and should not be a substitute for a chemical analysis.
-
Page 6: Ph Menu
Technical Manual v2.0 PHENIX PH MENU This menu is used to access the pH regulation settings. To access the pH Menu, simply press the key. keys are used to scroll through this menu. The different displays in this menu are: Dosage pH = pH- This screen allows you to choose the regulation mode. - Page 7 NOTE: As PHENIX injects the product into the pool, the value previously defined is decreased. When this value reaches 0, the PHENIX pump is blocked. To re-enable operation of the pump, the user should reset the container volume as described below.
-
Page 8: Oxidant Menu
Ox Calibration Calibration of the ORP sensor is carried out in the same way as for the pH sensor. But with a single measurement point. Calibration is carried out using the 650mV solution supplied with the PHENIX device. CCEI page 8... -
Page 9: Settings Menu
French, English, German, Spanish, Italian, Portuguese, Dutch or Czech. Reset to zero This screen is used to reinitialise and reset to 0 the different PHENIX counters. The time counter and the total quantity of liquid injected are reset to 0. -
Page 10: Hydraulic Connection
Technical Manual v2.0 PHENIX HYDRAULIC CONNECTION Suction strainer to plunge into the liquid corrector container (PHminus or PHplus) Use a pipe saddle. Chlorinator Screw the injector into Control the saddle using TEFLON Flow detector Connect the sensors For connection with the pool, the pipe saddle, sensor holder and sensor must be used. -
Page 11: Installation Diagram
INSTALLATION DIAGRAM The various parts of the PHENIX that must be positioned on the pool's piping system are: The pH sensor: must be positioned directly after the filter with other measurement appliances if required. Positioning is done using a pipe saddle with a 63 or 50 mm diameter. -
Page 12: Electrical Connection
Technical Manual v2.0 PHENIX ELECTRICAL CONNECTION Before connecting the PHENIX to the mains, it is essential to check the power protection using a 30mA differential device. The power supply must be permanent and properly protected against any possible overvoltage and overloads. - Page 13 PHENIX Installing your PHENIX with a CCEI LIMPIDO EZ chlorinator: Cut the control cable supplied with the PHENIX so you have 2 cables with 1 connector on one side, 2 wires on the other; Connect the LIMPIDO EZ flow detector to the PHENIX “Flow detector” input (under the...
- Page 14 Installing your PHENIX with a CCEI ZELIA ZLT chlorinator: Cut the control cable supplied with the PHENIX so you have 2 cables with 1 connector on one side, 2 wires on the other; Connect the flow detector (optional, ref. KT200006) to the “Flow detector” input of the...
-
Page 15: Sensor Maintenance
Technical Manual v2.0 PHENIX Installing PHENIX with a chlorinator from another manufacturer: CAUTION: This operation requires full knowledge of the equipment to be connected and must be carried out by a professional. A wiring error could seriously damage the equipment. - Page 16 Date of sale: ............... Serial no.: ..............Declaration The company Bleu Electrique SAS (FR 47 403 521 693) hereby declares that the PHENIX product meets the safety and electromagnetic compatibility requirements of European Directives 2006/95/EC and 2004/108/EEC. Emmanuel Baret, Marseilles, 03/08/2015...