Download Print this page
Samsung DMT800RHS/XAA Troubleshooting Manual

Samsung DMT800RHS/XAA Troubleshooting Manual

Hide thumbs Also See for DMT800RHS/XAA:

Advertisement

Quick Links

Models:
DMT800RHS/XAA
DMT800RHB/XAA
DMT800RHW/XAA
Detergent with a separate rinse additive in the dispenser gives better drying performance.
For tough baked on soils an Enzyme detergent is better at hydration of the food soils.
For staining such as tomato, coffee and tea, a detergent with a higher phosphate content and Chlorine bleach will work
on the stains much better than an Enzyme based detergent.
Dishwasher Cycle Chart — Air diffusion condensing Dry System
Cycle
Pre-
Pre-
wash
wash
1
2
Normal
Flex
Heavy
Deli-
x
cate
Pot &
131˚
Pans
F
(55˚C
Quick
x
+
Smart
Flex
Auto
• The numbers in parentheses in the Last Rinse column represent the temperature when you select Sanitize.
• When you select the Smart Auto or Normal cycle, you can eliminate the Flex (flexible) steps depending on the soil level
of the dishes.
• The wash time varies depending on the steps or options you add, and on the pressure and temperature of the supplied
water.
• When you select Half Load or Storm Wash, the cycle sequence remains the same. (DMT800)
• If "Rinse Refill" lamp lights during a cycle, the dishwasher adds 30 more minutes to the Drying cycle automatically after
the Clean light illuminates.
IMPORTANT SAFETY NOTICE – "For Technicians Only" This service data sheet is
intended for use by persons having electrical, electronic, and mechanical experience
and knowledge at a level generally considered acceptable in the appliance repair trade.
Any attempt to repair a major appliance may result in personal injury and property
damage. The manufacturer or seller cannot be responsible, nor assume any liability for
injury or damage of any kind arising from the use of this data sheet.
Which Detergent Ingredients Give Best Dishwasher Performance
Main wash
Rinse
1
120 ~ 138 ˚F
Flex
(49 ~59 ˚C)
140 ˚F (60
˚C)
122 ˚F (50
˚C)
149 ˚F (65
˚C)
140 ˚F (60
x
˚C)
122 ˚F~138
Flex
˚F
(50~59 ˚C)
Fast Track Troubleshooting
Publication # tsDMT800RF Creation Date 08/18/2010
Rinse
Rinse
Last Rinse
2
3
[Sanitize]
x
136 ˚F (58 ˚C)
[162 ˚F (72 ˚C)]
158 ˚F (70 ˚C)
[162 ˚F (72 ˚C)]
x
140 ˚F (60 ˚C)
158 ˚F (70 ˚C)
[162 ˚F (72 ˚C)]
x
140 ˚F (60 ˚C)
[162 ˚F (72 ˚C)]
x
136 ˚F (58 ˚C)
[162 ˚F (72 ˚C)]
Dry
Water
Time
(min.)
[gal(ℓ)]
(min.)
30
3.6~6.7
110~132
(13.6~25.2)
40
8.1 (30.6)
152
30
4.7 (17.7)
107
40
8.1 (30.6)
157
15
4.7 (17.7)
59
(+15)
30
4.7~6.7
100~149
(17.7~25.2
)
1

Advertisement

loading

Summary of Contents for Samsung DMT800RHS/XAA

  • Page 1 Models: and knowledge at a level generally considered acceptable in the appliance repair trade. DMT800RHS/XAA Any attempt to repair a major appliance may result in personal injury and property DMT800RHB/XAA damage.
  • Page 3: Dry System

    T202-(CN101-3) Main PCB Heater (Red-Yel) (120vac) CN102 1-6 (S/Blu-S/Blu) +5vdc 2-6 (S/Blu-S/Blu) +12vdc CN501 3-1 +5vdc T201 L1 (Blk) (120vac) CN202 1-(CN101-3) Valve (Brn-Yel) 120vac CN101 Power CN302 5-(CN101-3) Pump (Org-Yel) 120vac 1 Ground (Yel/Grn) 1-Half Load Sense (Blk) 3 120vac N (Yel) 2-Turbidity Transmitter (Red) 5 120vac L (Blk) CN201...
  • Page 4 Leaking Code Moisture creates resistance between the pins. ALWAYS clean the area below the pins after troubleshooting. Check Pump Ass’y for proper twist lock. Condensation may form on the tray from uninsulated outside walls or large hole in the floor to a cold basement. Check Drain Hose for cut or small hole.
  • Page 5 Error Codes - DMT800 series Code Meaning Occurring condition Expected condition sym- When 0.2V or below, or 4.5V or above is main- Temp sen- Thermistor terminal is not connected tained for over 3 seconds Possible defect : Thermistor , Main Error When the temperature change is 4 or less...
  • Page 6 SVC inspection Mode- DMT800 series • Press the ‘Heavy’ + ‘Delicate’ + ‘Power’ buttons at the same time for two seconds to enter Service Inspection Mode. • All LEDs are displayed for the first two seconds and then Software-Ver. will be indicated. •...
  • Page 7 SVC inspection Mode- DMT800 series • Press the ‘Heavy’ + ‘Delicate’ + ‘Power’ buttons at the same time for two seconds to enter Service Inspection Mode. • All LEDs are displayed for the first two seconds and then Software-Ver. will be indicated. •...

This manual is also suitable for:

Dmt800rhb/xaaDmt800rhw/xaa