Advertisement
Operating
Instructions
Getting Started:
Safety Note!
The edges of the stainless steel tape may be sharp. Use caution when removing tape from your tool or installing a new roll of tape.
Letters in bold blue correspond to the illustration on front page.
Loading tape - The GRD400 is presented with one roll of
SS tape already installed as part of our factory adjustment
and testing. To refill, follow these simple instructions:
1)
Place the tool in front of you on a flat surface, open
the SS tape door
pieces of SS tape in the storage cavity or in between
the tape feed rollers (O).
2)
Hold the next roll of SS tape securely and remove the
strip of plastic tape used for shipping purposes taking
care to not allow the roll to unravel.
3)
Place the roll of SS tape into the tape storage cavity
(J) allowing 2-3" of material to extend from the tape
slot and close the SS tape door.
4)
Feed the SS tape into the two rollers
squeeze the handle
advance the SS tape.
Embossing your SS tape -
squeezing the handle while turning the character wheel!
1)
Turn the character wheel
centered in the character viewing window (B).
2)
Squeeze the embossing handle
Release the embossing handle fully before selecting
the next character. Each time the handle is squeezed
the SS tape will advance one space.
3)
Add a space between words or numbers by squeeze-
ing the handle gently ½ way and releasing the handle.
Also, a space can be added by releasing the handle
completely and turning the SS tape advance knob
one click in a clockwise direction.
Adjusting the depth of characters –
impression which is too deep may cause the SS tape to
wrinkle between the characters and may jam in the tool.
1)
This adjustment may be used to optimize the clarity of
the characters on the tape. Determine the best setting
by turning the adjustment knob
symbol.
Cutting the tape and label - This tool is equipped with a
heavy duty cutter bar
(H)
1)
Advance the tag forward far enough to clear the
embossed
lettering
Centering.
2)
Lift the cutter handle up and forward to cleanly cut the
band.
Retracting the SS tape – The SS tape may have been
advanced too far or you may need to re-center the label.
1)
While pulling back the Tape Pawl (N), turn the Tape
Advance Knob
(I)
counter-clockwise.
BAND-IT-IDEX, Inc.
A Unit of IDEX Corporation
4799 Dahlia Street
Denver, CO 80216-3070 USA
P: 1-800-525-0758
F: 1-800-624-3925
(J)
and remove any remaining
(O)
and begin to
(K)
half-way several times to
!! Important !!
Avoid
(A)
until the desired letter is
(K)
firmly, one time.
!! Important !!
(M)
towards the + or –
which will cut SS tags to length.
or
see
the
directions
www.BAND-IT-IDEX.com
Centering the text on the ID Tag – The tool is equipped with a
retractable tag centering guide
1)
After cutting the previous label, emboss your next label.
2)
Pull the tag centering guide
retracted position.
3)
Advance the tape until the last character is even with the
letter "L" on the tag centering guide.
4)
Cut off the tag, the tag should be centered.
5)
To center the tag with a short lead, first retract the tag until
tape edge is at the start line. Emboss the next label;
advance the tape until the last character is even with the
letter "S" on the tag centering guide
6)
Cut off the tag which is now centered.
Punching holes and slots in your ID Tag – The tool is capable
of punching holes (C), cable tie slots
1)
Insert one end of the tag in the appropriate slot on the front
of the tool. The slots are marked appropriately.
2)
!! Important !!
a.
The letters must face down for proper positioning of
cable tie slot.
b.
Plan enough space for slot to be clear of letters and
punched holes.
3)
Lift the cut-off handle
easily.
TROUBLESHOOTING: To ensure smooth operation and free
movement of the tape:
1)
The tape must be flat and free of kinks and burrs on the
leading edge.
An
2)
Check that the embossed characters on the tape are not set
so deep that the tape appears wrinkled at the top and bottom
edges.
3)
When the hole punch is used, the punched hole must be
clean and free of excessive burrs.
4)
Before withdrawing the tape backward beyond the front edge
of the cutter, ensure that the front edge of the tape is flat and
free of burrs.
5)
After withdrawing the tape backward, take up the slack of the
tape below the hands by winding excessive tape into the
holder before further usage.
for
7)
Tape is slipping- Clean the rollers
and alcohol while turning the rollers several revolutions
8)
Regularly check for cut SS tape scrap build up in the bottom
of the tool (L).
9)
Warranty information :
www.band-it-idex.com/warranty.html
Page 2 of 2
GRD400 SS TAPE
EMBOSSER
(D)
to allow a short or long lead.
(D)
forward from its normally
(D).
(F)
or both.
(H)
and perform the punch operation
(O)
by using a soft cloth
Document # P46550 Rev. -
© Copyright
BAND-IT-IDEX, Inc. 2008
All rights reserved
Advertisement
