Avlite Systems draws on more than 25 years of experience in the design and manufacture of navigation aids, and particular care has been taken to ensure your product gives years of trouble-free service.
LED Technology All Avlite lights use the latest advancements in LED (Light Emitting Diode) technology as a light source. The major advantage of LED’s over traditional light sources is well established in that they typically have an operational life in excess of 100,000 hours, resulting in substantial savings to maintenance and servicing costs.
3.0 AV-OL-CTRL-T1 The AV-OL-CTRL-T1 Obstruction Lighting Controller is an application specific control and monitoring system to provide a full turnkey solution for A0/I1 structures up to 45 meters (150 feet). These include telecommunication and utility towers, wind turbines, cranes, buildings and other tall structures.
The system can also be configured to send out SMS text messages or e-mail alerts to designated operators should alarm conditions be triggered, such as low voltage or light failure. Please contact Avlite for operational information for the Monitoring & Control options. •...
305/12 Length (mm/inches) 152/6 Mass (kg/lbs) 7.3/16 Service Life 12 years + Intellectual Property Trademarks AVLITE® is a registered trademark of Avlite Systems Compliance EN61000-6-3:2007, EN61000-6-1:2007 FCC 47 CFR Part 15, subpart B Quality Assurance ISO9001:2015 Protection Rating IP65/NEMA4X Other...
• Dispose of the product according to the local laws and regulations for your region, for example, at a recycling centre that accepts electronic devices. Latest products and information available at www.avlite.com...
6.0 Operation and Setup Avlite’s AV-OL-CTRL-T1 Obstruction Lighting controller connects to one component: A single L-810 steady burning, Dual Obstruction Light fixture. The L-810 Dual Light operates as a concurrent fixture where both individual lights operate at the same time. The fixture automatically switches between day and night mode via an integrated Photocell.
The Controller is available in two input power configurations; a universal AC (90-264 VAC) or DC (12-48 VDC) and comes with remote monitoring via Star2M with either GSM or Satcom telemetry types as options. 6.1.2 Interface Wiring LI Dual Light Fixture T1 Controller Latest products and information available at www.avlite.com...
7.0 Unpacking, Installation, Wiring and Setup 7.1 Unpacking Unpack all hardware and inspect for damage. If there is any damage, please contact your Avlite Office. Retain original packing material for possible future use in shipping. 7.2 Installation WARNING: Confirm that the power switch is toggled to the OFF position when power is connected.
Note: The sequence of steps can be adjusted for site requirements. Wire and test the system on ground level. Conduct a basic functional check to ensure that the control unit is operating as expected. Refer to Section 7.3 Testing Procedure. Latest products and information available at www.avlite.com...
Page 14
Mount the Control Unit The Control Unit should be mounted in a reasonable location at eye level to ensure that it is easily accessible for servicing and maintenance. There should be plenty of clearance around all sides to allow direct access when the door of the control unit is completely open. Attach the required mounting hardware to the top and bottom of the Control Unit.
Page 15
• Connect the green alarm conductor from the low intensity light fixture to the Alarm terminal block in the Control Unit Refer to the AV-OL-KT-A0/I1 Installation and Service Manual for recommended cable sizes. Latest products and information available at www.avlite.com...
Page 16
Wiring the Control Unit: AC Installation: Avlite has supplied a cord grip for installation of the power cord in the bottom of the Control Box. Connect the incoming power conductors to the appropriate terminals (L1 and L2) on the power switch in the Control Box.
Installation & Service Manual 7.3 Testing Procedure Note: Avlite recommends that all testing be done during the day. TPower the system on. Check that no circuit breakers have tripped. Cover each light fixture in the low intensity obstruction light and ensure they turn on.
10.0 Troubleshooting Problem Possible Cause Solution LI Dual Obstruction Wiring of Light to • Check the wiring of the light Light will not activate Power supply and ensure proper connectivity with power supply. • If wiring functions properly, use an alternate power source to check the light.
Page 19
AV-OL-CTRL-T1 - Obstruction Light Controller Installation & Service Manual Notes Latest products and information available at www.avlite.com...
Page 20
Avlite Solution Verticals available Airfield Heliport Obstruction We believe technology improves navigation avlite.com info@avlite.com Avlite Systems Avlite USA LLC Avlite Asia Pte Ltd Australia Singapore +61 (0)3 5977 6128 +1 (603) 737 1311 +65 6908 2917...
Need help?
Do you have a question about the AV-OL-CTRL-T1 and is the answer not in the manual?
Questions and answers