master mechanic TV200 Instruction Manual

6.0 volt 2-speed cordless drill
Table of Contents

Advertisement

Available languages

Available languages

*TV200 / 390001
11/14/03
7:28 AM
INSTRUCTION
MANUAL
6.0 Volt 2-Speed Cordless Drill
TV200
KEY INFORMATION YOU SHOULD KNOW:
•Drill must be charged for 16 hours before initial use.
•Charger may hum; batteries or charger may become warm
during charging.
•Tighten chuck using all three holes.
SAVE THIS
MANUAL FOR
FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
Page 1
1-800-544-6986
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock, fire
and/or serious personal injury.
Work Area
• Keep your work area clean and well lit. Cluttered benches and dark
areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create
sparks which may ignite the dust or fumes.
• Keep bystanders, children, and visitors away while operating a
power tool. Distractions can cause you to lose control.
Electrical Safety
• Do not abuse the cord. Never use the cord to carry the tool. Keep
cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords may create a fire.
• A battery operated tool with integral batteries or a separate battery
pack must be recharged only with the specified charger for the
battery. A charger that may be suitable for one type of battery may
create a risk of fire when used with another battery.
• Use battery operated tool only with specifically designated battery
pack. Use of any other batteries may create a risk of fire.
Personal Safety
• Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention
while operating power tools may result in serious personal injury,
1
GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS
SAVE THESE INSTRUCTIONS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TV200 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for master mechanic TV200

  • Page 1 *TV200 / 390001 11/14/03 7:28 AM Page 1 INSTRUCTION GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS MANUAL 1-800-544-6986 WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
  • Page 2 *TV200 / 390001 11/14/03 7:28 AM Page 2 • Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
  • Page 3: Specific Safety Rules

    *TV200 / 390001 11/14/03 7:28 AM Page 3 metal objects that can make a connection from one terminal to The label on your tool may include the following symbols. another. Shorting the battery terminals together may cause sparks, V ....volts burns, or a fire.
  • Page 4: Two Speed Operation

    *TV200 / 390001 11/14/03 7:28 AM Page 4 2. DO NOT charge the batteries in an air temperature below +40°F Trigger Switch & Reversing Button or above +105°F. This is important and will prevent serious The drill is turned ON and OFF by pulling and releasing the trigger damage to the batteries.
  • Page 5: Operation

    *TV200 / 390001 11/14/03 7:28 AM Page 5 • Use sharp drill bits only. or with spade bits. These bits should be sharp and should be pulled out frequently when drilling to clear chips from the flutes. • Support and secure work properly, as instructed in the Safety Instructions.
  • Page 6 Take the two body halves apart and you will find the Lubrication battery pack. Lift the battery pack out and pull off the terminal clips. MASTER MECHANIC tools are properly lubricated at the factory and Two Year Quality Guarantee are ready for use.
  • Page 7: Renseignements Importants

    *TV200 / 390001 11/14/03 7:28 AM Page 7 GUIDE IMPORTANTES MESURES DE SÉCURITÉ - POUR TOUS LES OUTILS ALIMENTÉS PAR PILES D’UTILISATION 1 800 544-6986 AVERTISSEMENT! Lire et comprendre toutes les directives. Le non- respect de toutes les directives suivantes présente des risques de secousses électriques, d’incendie ou de blessures graves.
  • Page 8: Sécurité Personnelle

    *TV200 / 390001 11/14/03 7:28 AM Page 8 SÉCURITÉ PERSONNELLE approprié fonctionne mieux et sûrement lorsqu’on s’en sert à son rendement nominal. • Demeurer vigilant, prendre soin et faire preuve de jugement • Ne pas se servir de l’outil lorsque l’interrupteur est défectueux. Le lorsqu’on utilise un outil électrique.
  • Page 9 *TV200 / 390001 11/14/03 7:28 AM Page 9 rechange identiques. Respecter les consignes relatives à l’entretien 3. Brancher le chargeur dans une prise standard. du présent guide d’utilisation. Il y a risque de secousses électriques ou 4. Laisser l'outil de cette façon pendant 16 heures.
  • Page 10 *TV200 / 390001 11/14/03 7:28 AM Page 10 ne pose aucun problème de sécurité, mais cela peut grandement enlever des attaches. Il faut d'abord relâcher l'interrupteur à détente réduire la durée utile de la pile. avant de déplacer l'inverseur de marche.
  • Page 11 *TV200 / 390001 11/14/03 7:28 AM Page 11 • Bien saisir la perceuse afin d'en maîtrise l'effet de torsion. forcer afin d'éviter de casser les matériaux friables. Une production uniforme de poussière à débit moyen indique un perçage convenable. • NE PAS ACTIONNER À PLUSIEURS REPRISES LA DÉTENTE D'UNE PERCEUSE BLOQUÉE DANS LE BUT DE LA DÉCOINCER AU RISQUE...
  • Page 12 FORETS À BOIS – Diamètre maximal de 10 mm (3/8 po). Lubrification Les outils MASTER MECHANIC sont lubrifiés en usine et prêts à être utilisés. Garantie de qualité de deux ans Une garantie de deux ans couvre le produit contre les vices de matière et de fabrication.
  • Page 13 *TV200 / 390001 11/14/03 7:28 AM Page 13 MANUAL DE REGLAS GENERALES DE SEGURIDAD - PARA TODAS LAS HERRAMIENTAS OPERADAS CON BATERÍAS INSTRUCCIONES ¡ADVERTENCIA! LEA Y COMPRENDA TODAS LAS INSTRUCCIONES. No hacerlo puede originar riesgos de choque eléctrico, incendio y lesiones personales de gravedad.
  • Page 14: Reglas Específicas De Seguridad

    *TV200 / 390001 11/14/03 7:28 AM Page 14 cuando opere una herramienta eléctrica. No opere ninguna herramienta si se de apagado antes de hacer cualquier ajuste, cambio de accesorios o de encuentra fatigado o bajo la influencia de drogas, alcohol o medicamentos.
  • Page 15: Notas Importantes Sobre La Carga

    *TV200 / 390001 11/14/03 7:28 AM Page 15 operación en que la herramienta pueda hacer contacto con cableados Notas importantes sobre la carga ocultos. Al hacer contacto con un cable “vivo”, las partes metálicas de la 1. Después de uso normal, su taladro quedará cargado en 16 horas herramienta se vuelven “vivas”...
  • Page 16 *TV200 / 390001 11/14/03 7:28 AM Page 16 antes de desconectar el cargador de la unidad. Bajo ciertas reloj, coloque la broca dentro del portabrocas tanto como entre, y a condiciones, con el cargador conectado a la toma de corriente, la continuación, tire de ella lo necesario para que el portabrocas no haga...
  • Page 17: Operación

    *TV200 / 390001 11/14/03 7:28 AM Page 17 • NO APRIETE EL GATILLO DE UN TALADRO ATASCADO PARA la presión sobre el taladro, pero no al grado que se despostillen los HACER PRUEBAS DE ENCENDIDO Y APAGADO, PUES PODRIA materiales. La salida continua de volutas de polvo indica que se esta DAÑARLO.
  • Page 18: Mantenimiento

    Lubricación regiones. Las herramientas MASTER MECHANIC se lubrican apropiadamente en la El programa RBRC™ hace más sencillo para usted deshacerse de sus baterías fábrica y están listas para usarse. desgastadas con los distribuidores de baterías de níquel-cadmio de su localidad.
  • Page 19 *TV200 / 390001 11/14/03 7:28 AM Page 19...
  • Page 20 *TV200 / 390001 11/14/03 7:28 AM Page 20 Cat. No. TV200 Form No. 390001 (JAN99-1)

Table of Contents