Advertisement
2. INTRODUCTION
Mobile workshop extractor suitable for attachment to most static workshop machines including bandsaws, table saws, scroll saws, planers and
sanders. Supplied with 2m of Ø100mm suction ducting.
3. SPECIFICATION
Model no ................................................................. SM47.V3
Airflow ........................................................................ 618cfm
Flex hose diameter ..................................................... 100mm
Flex hose length ......................................................... 200mm
Impeller diameter ....................................................... 250mm
Intake diameter .......................................................... 125mm
Motor power ................................................................1500W
4. CONTENTS
Collector Body with Motor
Seal
Base plate
Hose
Hose Clamp x 2
Collector
Support Rod, Filter Bag
Outlet
5. ASSEMBLY
Note: Numbers in brackets are the item numbers on the parts diagram and in the parts list.
5.1.
Attach the four castors (1) to the underside of the base (3) using screws (23), washers (16) and nuts (19). Support base (3) on battens, or
similar, raising castors clear of floor to give stability for the following assembly tasks.
5.2.
With screws (6) and washers (4) attach motor base (5) to base (3).
5.3.
Attach motor (8) to motor base (5), so that collector body is positioned as shown in parts diagram, with screws (6) and washers (4).
5.4.
Attach fan housing (38) feet to base plate (3) with screws (6) and washers (4).
5.5.
Install outlet (30) to fan housing (38) using packing (29), screws (15), washers (16) and nuts (19).
5.6.
Attach collector supports (37) to base with screws (12) and washers (4) and to collector (33) with screws (6) and washers (4).
Note that upper bag support (13) is fitted to the collector (33) with the same screws as the collector support (37).
5.7.
Fit (upper) filter bag (35) over upper bag flange on collector (33) and secure by tightening built-in strap. Hook loop on end of bag (35)
over support arm (13). Fit second (collector) bag (36) to lower bag flange on collector.
Note: Bag clamps (34) are provided and may be used for additional bag security.
5.8.
Install hose (32) between outlet (30) and collector (33) and retain with hose clamps (31).
5.9.
Push-fit inlet (24) to inlet cover (25)
6. OPERATION
WARNING! Before operating the extractor ensure that you read, understand and apply the safety instructions in Section 1.
‰
6.1.
Confirm that supply voltage matches the voltage shown on the motor data plate and that the motor switch (9) is 'Off'.
6.2.
Connect extractor hose (39) to the inlet (24) and attach other end to extractor point on equipment. If only one extractor hose is to be
used ensure that the unused inlet is closed with the cap provided.
WARNING! DO NOT operate extractor without the hose(s) attached.
‰
6.3.
Plug into mains supply and press motor switch 'On'.
6.4.
Ensure that the lower bag is emptied of dust and chips on a regular basis and is not allowed to become full.
Note: Fitting a reducer to the extraction hose will reduce the volume of dust extracted.
WARNING! This unit is not suitable to be used to extract dust via a piped system.
‰
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on technical@sealey.co.uk or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
Filter/Collector Bag x 2
Support, Collector x 3
Screws, Nuts, Washers (1 bag)
Inlet
Bag Clamp x 2
Inlet Hose (2m)
Castors x 4
01284 703534
Original Language Version
sales@sealey.co.uk
www.sealey.co.uk
VSE6940 Issue:1 30/11/20
Advertisement
