Modular crescent cuber including
condensing unit models hoshizaki srk-15j; hoshizaki srk-15j3 (60 pages)
Summary of Contents for Hoshizaki SRM-45A
Page 1
/ user with the essential information for the proper installation and continued safe use and maintenance of the product. ●Please preserve this booklet for any further consultation that may be necessary. Manufacturer: HOSHIZAKI (SUZHOU) CO., LTD No. 15 Qingqiu Street, Suzhou Industrial Park, Suzhou 215126.China L1M078101(011518) ...
IMPORTANT SAFETY INFORMATION Throughout this manual, notices appear to bring your attention to situations which could result in death, serious injury or damage to the unit. WARNING Indicates a hazardous situation which, If not avoided, could result in death or serious injury. CAUTION Indicates a hazardous situation which, If not avoided, could result in minor or moderate injury.
Ⅰ . INSTALLATION INSTRUCTIONS 1. CONSTRUCTION Top Panel Door handle Name Plate Storage Bin Air Filter Louver Power Switch [SRM-45A] Top Panel Door handle Storage Bin Name Plate Air Filter Louver Power Switch [SRM-60/80A] 2 ...
Top Panel Door handle Storage Bin Name Plate Front Panel - Middle Air Filter Louver Power Switch [SRM-105/125A] 2. ACCESSORIES SRM-45A SRM-60A SRM-80A SRM-105A SRM-125A Instruction Manual Scoop Instruction Manual Scoop 3 ...
3) Remove the protective film from the exterior. If the icemaker is exposed to the sun or to heat, remove the film after the icemaker cools. 4) Remove the shipping tape holding accessories by opening the door 5) Remove the package of accessories. Check the contents according to “2.ACCESSORIES” Bin Door [SRM-45A] 4 ...
Page 7
Bin Door [SRM-60/80A] Bin Door [SRM-105/125A] 5 ...
Left Ice maker 0 cm Right Front 【NOTE: SRM-45A:L=1cm; SRM-60/80/105/125A: L=15cm.】 In some high humidity environments, condensation may from inside the machine and drip onto the floor. Do not install where the floor can be affected by water. 5. INSTALLATION CAUTION Incorrect installation can cause harm to people, animals or other items, for which the manufacturer cannot be held responsible.
2) The outlet hose can be cut to appropriate length according to the position of the main drain nozzle. To prevent condensation, it can be coated some insulation pipe out of drain pipe. Stop Valve Note: Jointing compounds should be approved and suitable for potable water use. Outlet Hose Inlet Hose Inlet Hose Outlet Hose [SRM-45A] [SRM-60/80/105/125A] 7 ...
Ⅱ. OPERATING INSTRUCTIONS. CAUTION Do not put your hand into the back of the storage bin or the right side pump. The ice on the evaporator may drop off, a hard block of ice may suddenly break down, or pump motor may suddenly start-up, resulting in injury. Water Tank Storage Bin NOTICE...
Ⅲ. MAINTENANCE 1. CLEANING WARNING Before carrying out any cleaning or maintenance operations, unplug the icemaker from the electrical supply network. This appliance must not be cleaned by use of a water jet. CAUTION When using a neutral cleaner or sodium hypochlorite, thoroughly read and understand the instructions provided to prevent potential health problems.
Page 12
Cleaning agents must be the food class or a cleanser recommended by the manufacturer. Some solutions may damage the inner surface of the storage bin or corrode the metal parts. Cleaning liquid must be cleaned at any time unless otherwise specified by the manufacturer. 1.
Drain outlet of water tank 2. Screw 3 fixed Hex screws 1. Pull the overflow hose out Disassembly steps of water tank 1. Catch the left side of ice guide. 2. Press the right side of ice guide bracket. 3. Pull ice guide body forward until it is pulled out from the hole on the left side.
NOTICE After cleaning, be sure to install the air filter back to the original place. Air Filter Louver [ SRM-45/60/80/105/125A ] 2. PRECAUTIONS 1. The icemaker will have a larger “buzzing” sound when it begins to run because the operation is not stable at first time of powering-on or start.
3. FAULT AND TREATMENT Please operate the machine according to the instructions. If there are any exceptions, please check the follow table firstly. If it cannot be solved, please contact the authorized distributor or maintenance agency of our company in time. So as not to cause a loss to you.
Warranty repair should be completed by an approved manufacturer dealer or service agency using genuine manufacturer components. To obtain full details of your warranty and the approved service agency, please contact your dealer / supplier or the nearest manufacturer's service office. Repair Hotline: 400-720-6910 E-mail: service@hoshizaki.com.cn SPECIFICATION Model SRM-45A SRM-60A...
Need help?
Do you have a question about the SRM-45A and is the answer not in the manual?
Questions and answers