Advertisement
4. ASSEMbLY
fig.1
4.1.
Attach the wheels (fig.1.7) to the base bracket (fig.1.1) with bolts, washers,spring washers and nuts (figs.1.13,12,11 & 10)
4.2.
Build each side by joining two bases (fig.1.1.) together with an extension piece (outer) (fig.1.5). Secure with bolts (fig.1.8) and short
pins (fig.1.14)
4.3.
Couple the two sides by sliding an extension piece (fig.1.17) into the open end of each side and inserting an extension piece
(inner) (fig.1.18). Secure all with bolts (fig.1.8).
4.4.
Place a vertical post (fig.1.2) in each corner and secure with a bolt and long pin (fig.9). The post can be pinned at either of two heights.
5. OPERATION
5.1.
The dolly is supplied with three types of support (figs1.4, 15 & 16).
5.2.
Select the appropriate support and thread the spindle through the arm nut.
5.3.
Place the spindle in the vertical post with the arm nut resting on top. Adjust the supports to the appropriate configuration to receive
the vehicle. With the vehicle in place, fine adjustment is possible using the arm nuts.
5.4.
Move the loaded dolly slowly and smoothly. When not being moved, immobilise using the brake on each wheel.
6. MAINTENANCE
6.1.
Before each use check for broken, cracked, bent, or loose parts, or any visible damage. If any suspect item is found remove the dolly from
service and take necessary action to remedy the problem.
DO NOT use the trolley if believed to have been subjected to abnormal load or shock load.
6.2.
Keep the trolley clean and oil the wheel bearings periodically.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal of it according to local regulation
NOTE: It is our policy to improve products continually and as such we reserve the right to alter data, specifications and component parts without
prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Environmental Protection
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
Original Language Version
Item Part No
Description
1 . . .VMD002.01 Base with bracket
2 . . .VMD002.02 Vertical post
3 . . .VMD002.03 Arm nut
4 . . .VMD002.04 Saddle
5 . . .VMD002.05 Extension piece
(outer)
6 . . .VMD002.06 Base with bracket
7 . . .VMD002.07 Wheel
8 . . .VMD002.08 Bolt M10
9 . . .VMD002.09 Long pin 32mm
10 . . .VMD002.10 Nut.M10
11 . . .VMD002.11 Spring washer 10mm
12 . . .VMD002.12 Washer 10mm
13 . . .VMD002.13 Bolt M10 x 30
14 . . .VMD002.14 Short pin 12mm
15 . . .VMD002.15 Crutch (narrow angle)
16 . .VMD002.16 Crutch (wide angle)
17 . . .VMD002.17 Extension piece
18 . . .VMD002.18 Extension piece (inner)
s.
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
VMD002 Issue:2(SP) - 18/11/16
Advertisement
