Advertisement
2. INTRODUCTION
High velocity pedestal fan suitable for movement of huge volumes of air. carefully balanced and fully guarded blades provide quiet and safe
operation. Three-speed power selection, spring-assisted, height-adjustable stand and switchable head oscillation allow precise control of air flow
to exactly where it is needed. Fitted with Bs approved plug. suitable for use in industrial, commercial, agricultural and automotive workshop and
showroom applications.
3. SPECIFICATIONS
MODEL No:
Fan size:. . . . . . . . . . . . . . . . . . . . . . . . . . 610mm(24") . . . . . . . . 760mm(30")
speeds . . . . . . . . . . . . . . . . . . . . . .900/1120/1310rpm . . . . .740/820/920rpm
Maximum Airflow: . . . . . . . . . . . . . . . . . . . 220mtr³/min . . . . . . . . 227mtr³/min
Adjustable Overall Height: . . . . . . . . . . 1570-1990mm . . . . . . 1610-2030mm
Motor: . . . . . . . . . . . . . . . . . . . . . . . 230V-50Hz-220W . . . .230V-50Hz-170W
4. ASSEMBLY & OPERATION
4.1.
Assembly
4.1.1.
remove all packaging material and check contents with the parts list.
4.1.2.
Bolt the outer tubular stand to the base using the fixings supplied.
4.1.3.
slide the inner tubular stand into the outer tubular stand, fit and tighten the set knob to hold at desired height.
4.1.4.
Locate the motor housing onto the top of the inner tubular stand and fix in place using the nut, bolt and washers supplied.
4.1.5.
Place rear guard against the motor housing and fix in place using the 4 sets of nuts and washers.
4.1.6.
slide the fan onto the shaft and tighten the fixing screw with a phillips screwdriver.
4.1.7.
Hook the front guard into place at the top of the rear guard and then push the 7 clips around the edge of the guards into place so that
they engage both the front and rear guards.
4.2.
Operation
IMPOrTANT: Ensure that all safety instructions from section 1 have been read and understood before using the fan.
4.2.1.
set the fan on a level, dry surface.
4.2.2.
Plug the power cord into the mains supply.
4.2.3.
The fan features 3 speeds - selectable using the chain operated switch located at the back of the fan. This operates in a cycle -
OFF - LOW - MED - HIGH - OFF. LOW or MED settings will suit most needs, HIGH is used for maximum air movement.
4.2.4.
Adjust the direction of air flow up or down by loosening the knob and then tilting the fan assembly to the required angle, then retighten
the knob. To adjust the height setting, loosen the lower knob, set at desired height and then retighten knob. To oscillate the fan press
downwards on the knob on the top of the motor housing. To stop oscillation, pull the knob upwards.
4.2.5.
When not in use, disconnect from power supply and store in a safe, dry, childproof location.
5. CARE OF FAN
IMPOrTANT: Turn the control switch to OFF and disconnect fan from power supply before cleaning.
5.1.
Use only a soft, damp cloth to clean the fan.
5.2.
DO NOT submerse the fan in water and NEVEr allow water to drip into the motor housing.
5.3.
DO NOT use solvents or other chemicals to clean the fan.
5.4.
To clean the fan blades, loosen the 7 clips around the guards and then lift off the front guard from the top hook.
5.5.
Wipe the blades and guards.
5.6.
reassemble by hooking the front guard into place at the top of the rear guard and then push the 7 clips back into place so that they
engage both the front and rear guards.
5.7.
store the fan in its original box or otherwise cover the fan to protect it from dust.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
HvSF24
HvSF30
Sole UK Distributor, Sealey Group,
Kempson Way, suffolk Business Park,
Bury st. Edmunds, suffolk,
IP32 7Ar
Original Language Version
www.sealey.co.uk
01284 757500
Web
01284 703534
sales@sealey.co.uk
email
HVsF24, HVsF30 Issue: 3 - 22/03/10
Advertisement
