Sealey PT1170H.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
Only open bottomed Euro type pallets can be used to raise a load to

a higher level.
DO NOT use a faulty or damaged truck.

Before using the truck all parts and working mechanisms should be

checked for wear or damage. Pay particular attention to the wheels,
handle and fork lifting and lowering mechanism. Any parts found to be
worn, damaged or suspect should be repaired or replaced before the
truck is used.
All repairs must be carried out by an authorised Sealey service agent.

Personnel who operate the truck and those in the vicinity of operation

should wear safety shoes with reinforced toe caps at all times.
Never place any part of your body in the lifting mechanism or under

the forks or load.
DO NOT allow others to ride on the truck.

DO NOT lift or move unstable or loosely stacked loads.

Take special care when moving long, high or wide loads in order not

to dislodge the load by striking any architectural features, permanent
fixtures, vehicles or people in the area of operation.
Always ensure that the load is evenly distributed across the forks with

the centre of the load being at the halfway point of the length of the
forks.
DO NOT overload the truck - refer to the specification for maximum

permitted load.
If a load is left unattended even for a very short period of time it

should be lowered to the ground.
When not in use the truck should be left in the lowered position.

Ensure that the width and length of the forks is correct for the pallet to

be lifted.
Ensure that the truck is sufficiently inserted into the pallet to lift the full

width of the pallet.
Use the truck on level, flat, hard surfaces.

DO NOT use truck on sloping or uneven ground and DO NOT attempt

to negotiate curbs, steps or ramps.
The operator of the truck must be physically capable of controlling the

load selected; particularly in relation to stopping a rolling load.
fig.1
2. INTRODUCTION & SPECIFICATION
Heavy-duty high lift pallet truck suitable for the loading and unloading of light
commercial vehicles as well as warehouse and general handling duties.
Features twin stabilisers for extra balance when at maximum lift and an
ergonomic handle design for comfortable operation.
© Jack Sealey Limited
INSTRUCTIONS FOR:
PALLET TRUCK 1000kg 1170 x 540mm High Lift
MODEL No: PT1170H.V2
Specification.
Model No. . . . . . . . . . . . . . . PT1170H.V2
Capacity. . . . . . . . . . . . . . . . . . . . .1000kg
Minimum Height . . . . . . . . . . . . . . .85mm
Maximum Height . . . . . . . . . . . . .1240mm
Fork Spread . . . . . . . . . . . . . . . . . .225mm
Forks (Length x Width) 1170mm x 540mm
3.1
3.1.1 Note that the piston is constrained in the down position by a pin which
3.1.2 Identify and have ready the handle pivot pin which will have a roll pin
3.1.3 Slide the base of the handle into the handle mounting bracket which is
3.1.4 Drive the pin (fig.3A) through the aligned holes from left to right using a
3.1.5 Move the lever at the top of the handle into the lower position then pass
3.1.6 Lower the handle to depress the piston and remove the restraint pin
3.1.7 Place the handle in the
3.1.8 Press and hold down the
3.1.9 Slowly release the
3.1.10 Retain the handle
Original Language Version
3. ASSEMBLY
Assembling the handle to the truck. (see fig.2)
passes through holes in the handle mounting bracket. See fig.3B. DO
NOT remove this pin yet.
inserted through one end of it.
an integral part of the pump body and align the holes in the handle with
the holes in the bracket, see fig.3 below.
soft faced hammer and ensure that the roll pin rests in the groove in the
bracket as shown at fig.3D.
the chain with adjusting bolt and nut through the hole in the centre of
the handle pivot pin.
from the hole 'B' above the
piston, see fig 3B.
central 'raise' position.
foot pedal seen in fig.5A.
Slide the adjusting bolt and
nut at the end of the chain
throught the slot in the
other end of the pedal as
shown in fig.3C.
pressure from the foot
pedal. Check that the
adjusting nut is securely
situated beneath the foot
pedal.
assembly by driving
another roll pin through the
other end of the handle
pivot pin. See fig.3D.
fig.3
PT1170H.V2 Issue No:1- 12/02/14