Maintenance & Service; Caracteristiques Techniques - Skil 3158 Original Instructions Manual

EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 Read the instruction manual before use
4 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
5 Store tool/charger/battery in locations where temperature
will not exceed 50°C
6 Do not dispose of electric tools and batteries together
with household waste material
USE
• Charging battery
! read the safety warnings and instructions
provided with the charger
• Removing/installing the battery 2
• Battery level indicator 7
- press the battery level indicator button J to show the
current battery level 7 a
! when the lowest level of the battery indicator
starts flashing after pressing button J 7 b, the
battery is empty
! when 2 levels of the battery indicator start flashing
after pressing button J 7 c, the battery is not
within the allowable operating temperature range
• LED-light w
LED-light automatically lights on when activating the on/
off switch
! when LED-light starts flashing, the battery
protection is activated (see below)
• Battery protection
The tool is suddenly being switched off or prevented from
being switched on, when
- the load is too high --> remove load and restart
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C --> 2
levels of the battery level indicator start flashing when
pressing button J 7 c; wait until battery has returned
within the allowable operating temperature range
- the battery is nearly empty (to protect against
deep discharge) --> a low battery level or flashing low
battery level 7 b is shown by the battery level indicator
when pressing button J; charge battery
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
• On/off
- switch on/off the tool by pushing switch A 2 forward/
backwards
• Mounting/removing accessories 8
- connect nozzle F or G to intake port D
- for removing accessories handle vice-versa
• Empty dust compartment 9
! remove battery from tool before cleaning
- press release button B and remove dust compartment
E
- clean filter if necessary (see below)
- empty dust compartment
- mount dust compartment onto tool (make sure the dust
compartment clicks into place)
! never operate the tool without the necessary
filters
! optimal dust pick-up performance will only be
achieved with a clean filter and an empty dust
compartment
• Cleaning of dust filter q
- regularly clean the carefully removed dust filter by
gently tapping or brushing dirt off (wear dust mask)
- do not clean indoors in living areas
! do not wash filter with soap and water
- for picking up dust the dust filter needs to be dry
- if the dust filter is wet, it will clog quickly and be very
difficult to clean
! do not use a dust filter with tears or small holes;
replace it immediately
• Holding and guiding the tool w
! while working, always hold the tool at the grey-
coloured grip area(s)
- keep ventilation slots C 2 uncovered
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool clean (especially ventilation slots C 2 )
! remove battery from tool before cleaning
- clean ventilation slots C 2 regularly with a brush or
compressed air
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
b
Aspirateur sans fil
INTRODUCTION
• Cet outil convient pour le nettoyage léger par aspiration
et uniquement à un usage domestique
• Cet outil n'est pas conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3

CARACTERISTIQUES TECHNIQUES 1

6
3158