Advertisement
2. Changing Language
Maximus 4.0 supports multiple languages. To change the language of the tool, please do the
following:
1. On the home screen, tap on Settings -> Language & Input -> Languages.
2. Tap on "Add a language" , and then choose the desired language from the list.
3. Tap and hold the desired language and drag it to the top of the screen and then release it,
the system will change into the target language.
3. WLAN Setup
Once you're online, you can register your tool, update the diagnostic software and APK, surf
the Internet and send email on your network. Follow the steps below to proceed:
1. On the home screen, select Settings
2. Slide the WLAN switch to ON
, the tablet
networks.
3. Select a wireless network. If the chosen network is open
automatically. If the selected network is encrypted, a network password will need to be
entered.
4. Register & Update
Step 1: On the Home screen, tap on
"Maximus 4.0" to run the App, the
following screen displays. Tap on
"REGISTER UNIT" .
Step 2:
Tap on "ACTIVATE" button after
information* is entered.(*Note: Serial
number is a 12-digit number starting with
98 – you can find it on the back of your tool.
Verification code is an 8-digit number
stored in the Private & Confidential sheet.
Activation code is printed on the receipt, or
ask your dealer for it.)
5. Vehicle Connection
1. Locate Vehicle's DLC Port
The DLC (Data Link Connector) is typically a connector
where diagnostic code readers interface with the
vehicle's on-board computer.
For passenger cars, it is usually located on driver's side,
about 12 inches away from the center of dashboard. See
Figure DLC Location.
For commercial vehicles, it is generally located in the
driver's cab.
If the DLC cannot be found, refer to the vehicle's service manual for the exact location.
2. Vehicle Connection
1). OBD II Vehicle Connection
Connect one end of the OBD II extension cable to the OBD-16 connector, and the other end to
the vehicle's OBD II DLC port.
2). Non-OBD II Vehicle Connection
If the power supply on vehicle diagnostic socket is insufficient or the power pin is damaged,
you can get power in the following ways:
A. For Passenger Cars:
Battery Cable Clamps
VCI Dongle
OBD I Adapter
B. For Commercial Vehicles:
Battery Cable Clamps
VCI Dongle
OBD II Extension Cable
->
WLAN.
will start searching for all available wireless
, the tablet
will connect
To Vehicle's Battery
Non-16pin Connector
To Vehicle's Battery
Adapter Cable
Quick Start Guide
4. Register & Update(Cont.)
Step 3:
Tap on "RUN DIAGNOSTICS"
button to launch diagnostics.
Step 4:
Tap on
corner.
Step 5:
Tap on "UPDATE" button (*Note:
Red dot means new software is available).
Step 6:
Make sure all brands are selected,
tap on "Install" .
Tap on "OK" button when update is
complete. (*Note: Download and
installation will take approximately 10
minutes depending on the internet
connection.)
Quick Start Guide
6. Start Diagnostics
Maximus 4.0 supports three kinds of diagnosis approaches: Smart Diagnosis (MaxVIN),
Manual Diagnosis and Remote Diagnosis.
DLC Location
Maximus VINSCAN:
Through simple Wi-Fi communication between the Maximus 4.0 tablet and VCI dongle, you
can easily get the VIN (Vehicle Identification Number) information of the currently identified
vehicle. Once the VIN is successfully identified, the system will retrieve it from the remote
server and then guide you to vehicle information page without the necessity of step-by-step
manual menu selection (Early model may need manual selection.).
Remote Diagnosis:
This option aims to help repair shops or professional technicians launch instant messaging
and remote diagnosis, making the repair job getting fixed faster.
Manual Diagnosis:
In this mode, you have to diagnose a vehicle by performing the menu-driven command
manually.
For new users, please follow the operation chart shown below to get familiar with and start
using this tool.
Launch Maximus 4.0
App
Select vehicle
Select software version
and touch on "OK"
To Vehicle's DLC
Follow the prompts
on the screen
Note: For more detailed operations, please refer to the In-App User Manual stored
under "
To Vehicle's DLC
Pictures illustrated herein are for reference purpose only and this Quick Start Guide
is subject to change without notice.
on the top left-hand
Preparation
Before diagnosing, please make sure the following:
Switch the ignition on.
s
Vehicle battery voltage range should be 11V
s
~ 14V or 18V ~ 30V.
Throttle should be in a closed position.
s
Note:
To enjoy more capabilities and functions, it is
recommended you check for updates on a
frequent basis and keep synchronized with the
latest available software.
(Toolbox)" -> "About" -> "User Manual" .
MDMAX4
2101068-16
MDMAX4
2101068-16
Advertisement
