Ingco RT22008 Manual
  1. Manuals
  2. Brands
  3. Ingco Manuals
  4. Wood Router
  5. RT22008
  6. Manual

Ingco RT22008 Manual

Hide thumbs

Advertisement

Table of Contents

Router
EN
Router
RT22008 URT22008 RT22008-4 RT22008-8 RT22008-9
ingcoglobal
INGCO GLOBAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RT22008 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ingco RT22008

  • Page 1 Router Router RT22008 URT22008 RT22008-4 RT22008-8 RT22008-9 ingcoglobal INGCO GLOBAL...
  • Page 2 2|English The symbols in instruction manual and the label on the tool Double insulated for additional protection. Read the instruction manual before using. CE conformity. Wear safety glasses, hearing protection and dust mask. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
  • Page 3 3|English GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
  • Page 4 4|English a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
  • Page 5 5|English and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

  • Page 6: Specifications

    6|English SPECIFICATIONS Model No.: RT22008 RT22008-4 RT22008-8 RT22008-9 URT22008 Rated input power: 2200W 2200W Rated voltage: 220-240V~50/60Hz 110-120V~50/60Hz No-load speed: 14000-20000/min 14000-20000/min 1/4˝, 1/2 ˝ Diameter of collet : 6mm, 8mm, 12mm, 1/4˝, 1/2˝ Plunge capacity: 0-60mm 0~2-3/8˝ Manufacturer reserves the right to change specifications without notice.
  • Page 7 7|English 5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded.

  • Page 8: Specific Safety Rules

    8|English SERVICE 24. When servicing a tool, use only identical replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury.

  • Page 9: Functional Description

    9|English FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting the depth of cut Place the tool on a flat surface. Loosen the lock lever and lower the tool body until the bit just touches the flat surface.
  • Page 10 10|English Stopper block The stopper block has three adjusting hex bolts which raise or lower 0.8 mm (1/32”) per turn. You can easily obtain three different depths of cut using these adjusting hex bolts without readjusting the stopper pole. Adjust the lowest hex bolt to obtain the deepest depth of cut, following the method of “Adjusting depth of cut”.
  • Page 11 11|English Speed adjusting dial The tool speed can be changed by turning the speed adjust- ing dial to a given number setting from 1 to 6. Higher speed is obtained when the dial is turned in the direc- tion of number 6. And lower speed is obtained when it is turned in the direction of number 1.
  • Page 12 12|English OPERATION CAUTION: • Before operation, always make sure that the tool body automatically rises to the upper limit and the bit does not protrude from the tool base when the lock lever is loosened. • Before operation, always make sure that the chip deflector is installed properly.
  • Page 13 13|English Straight guide The straight guide is effectively used for straight cuts when chamfering or grooving. Install the straight guide on the guide holder with the wing bolt (B). Insert the guide holder into the holes in the tool base and tighten the wing bolt (A).
  • Page 14 14|English To install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws. 1. Templet guide 2. Screw 3. Base plate Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide sliding along the side of the templet.
  • Page 15 15|English Install the trimmer guide on the guide holder with the wing bolt (B). Insert the guide holder into the holes in the tool base and tighten the wing bolt (A). To adjust the distance between the bit and the trimmer guide, loosen the wing bolt (B) and turn the fine adjusting screw (1.5 mm or 1/16”...

  • Page 16: Maintenance

    10 minutes. Then check the tool while running and electric brake operation when releasing the switch trigger. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by INGCO Authorized Centers,always using INGCO replacement parts.
  • Page 17 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your INGCO tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.
  • Page 18 18|English RT22008,URT22008,RT22008-4,RT22008-8,RT22008-9...
  • Page 19 19|English SPARE PART LIST RT22008,URT22008,RT22008-4,RT22008-8,RT22008-9 No. Part Description No. Part Description Screw Switch Back cover Screw Controller Screw Housing Switch cover spring Cable Stator Cable protection sleeve Wind ring Adjust nut bearing Adjust lever Dust ring Guide rod Rotor Bolt...
  • Page 20 INGCO TOOLS CO.,LIMITED www.ingco.com MADE IN CHINA 1019.V02 RT22008 URT22008 RT22008-4 RT22008-8 RT22008-9...

This manual is also suitable for:

Urt22008Rt22008-4Rt22008-8Rt22008-9

Table of Contents